Fabrication of Microstructures on RB-SiC by Ultrasonic Cavitation Assisted Micro-Electrical Discharge Machining

Ultrasonic cavitation assisted micro-electrical discharge machining was used to fabricate microstructures on reaction-bonded silicon carbide. To aid the removal of debris from the machining gap and to obtain a good surface finish, carbon nanofibers were added into the dielectric fluid. The suspension of carbon nanofibers in the dielectric fluid and the cavitation bubble effect induced by the vibration of the dielectric fluid proved to be effective in reducing the deposition of tool material on the workpiece surface. The tool material deposition rate was found to be significantly affected by the vibration amplitude and the distance between the oscillator and the workpiece. With a hemispherical electrode and inclined workpiece, high accuracy micro-dimples could be obtained within a short time. A nanometer-level surface finish was successfully obtained on a hard-brittle RB-SiCmoldmaterial.

[1]  Keita Shimada,et al.  Statistical Approach Optimizing Slant Feed Grinding , 2012 .

[2]  Cheng-Tang Pan,et al.  Fabrication of gapless triangular micro-lens array , 2007 .

[3]  Yung-Chun Lee,et al.  Fabricating of aspheric micro-lens array by excimer laser micromachining , 2011 .

[4]  Jiwang Yan,et al.  Experimental investigation on material migration phenomena in micro-EDM of reaction-bonded silicon carbide , 2013 .

[5]  Wataru Natsu,et al.  Realization of Micro-EDM under Ultra-Small Discharge Energy by Applying Ultrasonic Vibration to Machining Fluid , 2013 .

[6]  Bülent Ekmekci,et al.  Debris and consequences in micro electric discharge machining of micro-holes , 2013 .

[7]  Jiwang Yan,et al.  Micro-cutting characteristics of EDM fabricated high-precision polycrystalline diamond tools , 2013 .

[8]  H. Weule,et al.  Micro-Cutting of Steel to Meet New Requirements in Miniaturization , 2001 .

[9]  D. Reynaerts,et al.  EDM technology and strategy development for the manufacturing of complex parts in SiSiC , 2010 .

[10]  Stephen T. Newman,et al.  State of the art electrical discharge machining (EDM) , 2003 .

[11]  Andreas Schubert,et al.  Analysis of the effect of vibrations on the micro-EDM process at the workpiece surface , 2011 .

[12]  Jiwang Yan,et al.  Carbon nanofiber assisted micro electro discharge machining of reaction-bonded silicon carbide , 2013 .

[13]  Han Huang,et al.  Fabrication of symmetrical section microfeatures using the electro-discharge machining block electrode method , 2002 .

[14]  Seung-Han Yang,et al.  A study on the effect of different vibration-assisted methods in micro-WEDM , 2013 .

[15]  Dominiek Reynaerts,et al.  Machining of three-dimensional microstructures in silicon by electro-discharge machining , 1998 .

[16]  George M. Whitesides,et al.  Fabrication of two-dimensional arrays of microlenses and their applications in photolithography , 2002 .

[17]  Wong Yoke San,et al.  Fabrication of different geometry cutting tools and their effect on the vertical micro-grinding of BK7 glass , 2012 .

[18]  Margaret B. Stern,et al.  Dry etching for coherent refractive microlens arrays , 1994 .

[19]  Jiwang Yan,et al.  Fabrication of deep micro-holes in reaction-bonded SiC by ultrasonic cavitation assisted micro-EDM , 2014 .

[20]  Myung-Chang Kang,et al.  Tool condition and machined surface monitoring for micro-lens array fabrication in mechanical machining , 2008 .

[21]  C. T. Pan,et al.  Fabrication of gapless triangular micro-lens array , 2007 .

[22]  Biing-Hwa Yan,et al.  Using a helical micro-tool in micro-EDM combined with ultrasonic vibration for micro-hole machining , 2006 .

[23]  B. Vyas,et al.  Stress produced in a solid by cavitation , 1976 .