Mode I fracture toughness determination with straight notched disk bending method

[1]  L. Tutluoglu,et al.  Investigation of proper specimen geometry for mode I fracture toughness testing with flattened Brazilian disc method , 2011 .

[2]  Q. Wang.  Formula for calculating the critical stress intensity factor in rock fracture toughness tests using cracked chevron notched Brazilian disc (CCNBD) specimens , 2010 .

[3]  Z. Cui,et al.  A comparison of two ISRM suggested chevron notched specimens for testing mode-I rock fracture toughness , 2010 .

[4]  G. Ruiz,et al.  Size of the Fracture Process Zone in High-Strength Concrete at a Wide Range of Loading Rates , 2010 .

[5]  Mihai O. Marasteanu,et al.  The fracture process zone in asphalt mixture at low temperature , 2010 .

[6]  Pedro Amaral,et al.  Assessment of fracture toughness in ornamental stones , 2008 .

[7]  Xiaozhi Hu,et al.  Size effect on specific fracture energy of concrete , 2007 .

[8]  B. Mohanty,et al.  Experimental Calibration of ISRM Suggested Fracture Toughness Measurement Techniques in Selected Brittle Rocks , 2007 .

[9]  B. Mohanty,et al.  Experimental calibration of stress intensity factors of the ISRM suggested cracked chevron-notched Brazilian disc specimen used for determination of mode-I fracture toughness , 2006 .

[10]  Xuekun Sun,et al.  Numerical evaluation of the effects of friction and geometric nonlinearities on the energy release rate in three- and four-point bend end-notched flexure tests , 2006 .

[11]  B. Mohanty,et al.  Fracture Toughness Measurements and Acoustic Emission Activity in Brittle Rocks , 2006 .

[12]  Chaoshui Xu,et al.  An Update on the Fracture Toughness Testing Methods Related to the Cracked Chevron-notched Brazilian Disk (CCNBD) Specimen , 2006 .

[13]  D. Hills,et al.  When does a notch behave like a crack? , 2006 .

[14]  Wang Qi-zhi.  Method for determination of dynamic fracture toughness of rock using holed-cracked flattened disk specimen , 2006 .

[15]  Soo-Ho Chang,et al.  Measurement of rock fracture toughness under modes I and II and mixed-mode conditions by using disc-type specimens , 2002 .

[16]  Z. Bažant.  Concrete fracture models: testing and practice , 2002 .

[17]  M. Elices,et al.  The cohesive zone model: advantages, limitations and challenges , 2002 .

[18]  Hiroshi Tada,et al.  The stress analysis of cracks handbook , 2000 .

[19]  Qi-Zhi Wang,et al.  Determination of fracture toughness KIC by using the flattened Brazilian disk specimen for rocks , 1999 .

[20]  Musharraf Zaman,et al.  Fracture toughness of a soft sandstone , 1998 .

[21]  M. Kuruppu.  Fracture toughness measurement using chevron notched semi-circular bend specimen , 1997 .

[22]  R. J. Fowell,et al.  Suggested method for determining mode I fracture toughness using Cracked Chevron Notched Brazilian Disc (CCNBD) specimens , 1995 .

[23]  Chengcheng Xu,et al.  The use of the cracked Brazilian disc geometry for rock fracture investigations , 1994 .

[24]  I. L. Lim,et al.  Fracture testing of a soft rock with semi-circular specimens under three-point bending. Part 2—mixed-mode , 1994 .

[25]  I. L. Lim,et al.  Stress intensity factors for semi-circular specimens under three-point bending , 1993 .

[26]  L. C. Schmidt,et al.  Rock fracture-toughness determination by the Brazilian test , 1993 .

[27]  Xiaozhi Hu,et al.  Fracture energy and fracture process zone , 1992 .

[28]  Z. Bažant,et al.  Determination of fracture energy, process zone longth and brittleness number from size effect, with application to rock and conerete , 1990 .

[29]  C. Haberfield,et al.  Determination of the fracture toughness of a saturated soft rock , 1990 .

[30]  J. Roegiers,et al.  FRACTURE TOUGHNESS DETERMINATION WITH THE MODIFIED RING TEST , 1988 .

[31]  Finn Ouchterlony,et al.  Suggested methods for determining the fracture toughness of rock , 1988 .

[32]  Zongqi Sun,et al.  Fracture toughness of stripa granite cores , 1986 .

[33]  A. R. Rosenfield,et al.  Fracture Toughness of Ceramics Measured by a Chevron‐Notch Diametral‐Compression Test , 1985 .

[34]  H. Takahashi,et al.  Simple Determination of the Effective Young's Modulus of Rock by the Compliance Method , 1985 .

[35]  K. P. Chong,et al.  New specimen for fracture toughness determination for rock and other materials , 1984 .

[36]  F. Ouchterlony.  Fracture mechanics methods for ceramics, rocks, and concrete , 1981 .

[37]  Finn Ouchterlony,et al.  Extension of the compliance and stress intensity formulas for the single edge crack round bar in bending , 1981 .

[38]  G. Szendi-Horvath.  Fracture toughness determination of brittle materials using small to extremely small specimens , 1980 .

[39]  A. J. Bush,et al.  Experimentally determined stress-intensity factors for single-edge-crack round bars loaded in bending , 1978 .

[40]  H. Awaji,et al.  Combined Mode Fracture Toughness Measurement by the Disk Test , 1978 .

[41]  L. M. Barker.  A simplified method for measuring plane strain fracture toughness , 1977 .

[42]  A. J. Bush,et al.  Experimentally determined stress-intensity factors for single-edge-crack round bars loaded in bending , 1976 .

[43]  J. Srawley.  Wide range stress intensity factor expressions for ASTM E 399 standard fracture toughness specimens , 1976, International Journal of Fracture.

[44]  B. Gross,et al.  Stress intensity factors for bend and compact specimens , 1972 .