Constructal vapor compression refrigeration (VCR) systems design

Abstract This paper introduces a mathematical model and a structured procedure to optimize the internal structure (heat exchanger areas) and pressure ratio of a vapor compression refrigeration system so that the refrigeration rate, the coefficient of performance (COP), and second law efficiency are maximized. The heat exchanger (condenser and evaporator) model equations are written based on the effectiveness-NTU method with the aim of achieving fast and accurate results for possible application in systems engineering design. The optimization is subjected to fixed system total heat transfer surface, A (or number of transfer units, N), and desired compressor power input, W cp . Two levels of optimization are investigated: (i) the compressor pressure ratio, p r = p c / p e , and (ii) the internal structure, which basically accounts for the relative sizes of evaporator and condenser heat transfer surfaces. The pressure ratio and the available heat exchanger area allocation are selected optimally so that system performance is maximized. In such condition, the refrigerant fluid morphs optimally in two and three sections, respectively, in the evaporator (superheating and two-phase), and condenser (superheating, two-phase, and subcooling), which are determined by the model. Three different refrigerants are tested with the model, i.e., R1234yf, R22, and R410A. Numerical results show that the optimized internal structure and pressure ratio are “robust” with respect to changes in refrigerant and system total number of transfer units. The optimized internal structure and pressure ratio are a result of an optimal balance among the several system irreversibilities (e.g., thermal contact between streams). The maxima found are sharp, showing a second law efficiency ∼400% variation within the tested range of the optimized parameters, highlighting the importance of exploring the system tradeoffs.

[1]  Sam Yang,et al.  A volume element model (VEM) for energy systems engineering , 2015 .

[2]  Sepehr Sanaye,et al.  Thermal and economical optimization of air conditioning units with vapor compression refrigeration system , 2004 .

[3]  Syed M. Zubair,et al.  Thermodynamic optimization of finite time vapor compression refrigeration systems , 2001 .

[4]  J.V. Amy,et al.  The state-of-the-art of integrated electric power and propulsion systems and technologies on ships , 2009, 2009 IEEE Electric Ship Technologies Symposium.

[5]  Cesare Pianese,et al.  Cost optimisation of supermarket refrigeration system with hybrid model , 2016 .

[6]  A. Abdel-azim.  Fundamentals of Heat and Mass Transfer , 2011 .

[7]  Adrian Bejan,et al.  Two design aspects of defrosting refrigerators , 1995 .

[8]  Adrian Bejan,et al.  Thermodynamic optimization of geometric structure in the counterflow heat exchanger for an environmental control system , 2001 .

[9]  J. MacArthur.  Transient heat pump behaviour: a theoretical investigation , 1984 .

[10]  A. Bejan.  Shape and Structure, from Engineering to Nature , 2000 .

[11]  M. J. Moran,et al.  Thermal design and optimization , 1995 .

[12]  Vikrant Aute,et al.  Comprehensive investigation of numerical methods in simulating a steady-state vapor compression system , 2008 .

[13]  Adrian Bejan,et al.  Minimum power requirement for environmental control of aircraft , 2003 .

[14]  Adrian Bejan,et al.  Power extraction from a hot stream in the presence of phase change , 2000 .

[15]  A. Bejan.  Entropy Generation Minimization: The Method of Thermodynamic Optimization of Finite-Size Systems and Finite-Time Processes , 1995 .

[16]  J. V. C. Vargas,et al.  Modeling, simulation and optimization of a vapor compression refrigeration system dynamic and steady state response , 2015 .

[17]  Haldun Dingeç,et al.  Thermoeconomic optimization of simple refrigerators , 1999 .

[18]  Andrew G. Alleyne,et al.  A dynamic model of a vapor compression cycle with shut-down and start-up operations , 2010 .

[19]  Sushil H. Bhavnani,et al.  Thermal Challenges in Next-Generation Electronic Systems , 2008 .

[20]  John T. Wen,et al.  Vapor compression refrigeration cycle for electronics cooling – Part I: Dynamic modeling and experimental validation , 2013 .

[21]  A. Bejan.  Advanced Engineering Thermodynamics , 1988 .

[22]  Bryan P. Rasmussen.  Dynamic modeling for vapor compression systems—Part I: Literature review , 2011, HVAC&R Research.

[23]  Adrian Bejan,et al.  Thermodynamic optimization of the match between two streams with phase change , 2000 .

[24]  Guillermo Bejarano,et al.  On the difficulty of globally optimally controlling refrigeration systems , 2017 .

[25]  J. M. Coulson,et al.  Heat Transfer , 2018, Finite Element Method for Solids and Structures.

[26]  Andrew G. Alleyne,et al.  A comparison between finite volume and switched moving boundary approaches for dynamic vapor compression system modeling , 2015 .

[27]  Lingen Chen,et al.  Optimal allocation of heat-exchanger area for refrigeration and air-conditioning plants , 2004 .

[28]  Farrokh Janabi-Sharifi,et al.  Review of modeling methods for HVAC systems , 2014 .