Performance assessment of contact heat pump drying

A comparative analysis is presented of a novel plate-type isothermal heat pump dryer and a conventional adiabatic heat pump dryer. The energy performance and drying capacity of each dryer type is investigated subject to operational constraints on the maximum acceptable relative humidity and temperature of air passing over the product. The analysis demonstrates that for applicable products, a significant opportunity exists for improving the energy efficiency of heat pump drying, by a factor of 2–3 times compared with current adiabatic heat pump dryers. The moisture extraction rate is also increased in the contact heat pump dryer, by a similar factor. However, these improvements are shown to be sensitive both to the impact of product thickness on heat transfer and to the relative humidity constraint. Copyright © 2010 John Wiley & Sons, Ltd.

[1]  C. Carrington,et al.  Variables affecting the in situ transesterification of microalgae lipids , 2010 .

[2]  Y. Chisti.  Biodiesel from microalgae. , 2007, Biotechnology advances.

[3]  A. Bejan.  Entropy generation minimization: The new thermodynamics of finite-size devices and finite-time processes , 1996 .

[4]  Gumpon Prateepchaikul,et al.  HEAT PUMP DRYER PART 2: RESULTS OF THE SIMULATION , 1997 .

[5]  S. Prasertsan,et al.  HEAT PUMP DRYERS: RESEARCH AND DEVELOPMENT NEEDS AND OPPORTUNITIES , 1998 .

[6]  C. G. Carrington,et al.  An empirical model for a heat pump dehumidifier drier , 1996 .

[7]  Shane Clements,et al.  Heat pump assisted continuous drying part 1: Simulation model , 1990 .

[8]  Shane Clements,et al.  Experimental verification of a heat pump assisted continuous dryer simulation model , 1993 .

[9]  C. G. Carrington,et al.  Second law limits in convective heat pump driers , 1988 .

[10]  C. G. Carrington,et al.  Calorimeter measurements of a heat pump dehumidifier: Influence of evaporator air flow , 1995 .

[11]  Siaw Kiang Chou,et al.  Performance of a heat‐pump assisted dryer , 1994 .

[12]  C. G. Carrington,et al.  Analysis of rankine cycle heat pump driers , 1988 .

[13]  C. G. Carrington,et al.  Influence of enhancing features on dehumidifier performance: laboratory measurements , 1995 .

[14]  F. A. Holland,et al.  The potential for heat pumps in drying and dehumidification systems I: Theoretical considerations , 1982 .

[15]  C. G. Carrington,et al.  Optimizing efficiency and productivity of a dehumidifier batch dryer. Part 1: capacity and airflow , 2000 .

[16]  Trygve Magne Eikevik,et al.  HEAT PUMP DRYING - NEW TECHNOLOGIES AND OPERATIONAL MODES FOR PRODUCTION OF A NEW GENERATION OF HIGH QUALITY DRIED PRODUCTS , 2004 .

[17]  Sukumar Devotta,et al.  Heat-pump-assisted dryer part 1: Mathematical model† , 1990 .

[18]  C. G. Carrington,et al.  USE OF DYNAMIC MODELLING FOR THE DESIGN OF BATCH-MODE DEHUMIDIFIER DRYERS , 2002 .

[19]  C. G. Carrington,et al.  Performance of a geared dehumidifier , 1997 .

[20]  F. A. Holland,et al.  The potential for heat pumps in drying and dehumidification systems II: An experimental assessment of the heat pump characteristics of a heat pump dehumidification system using R114 , 1982 .

[21]  S. Prasertsan,et al.  33002721 Heat Pump Dryer Part 3: Experimental Verification of The Simulation , 1997 .

[22]  Arun S. Mujumdar,et al.  SLUDGE DEWATERING AND DRYING , 2002 .

[23]  C. G. Carrington,et al.  Air Flow Patterns in Dehumidifier Wood Drying Kilns , 2004 .

[24]  Shane Clements,et al.  Heat pump assisted continuous drying part 2: Simulation results , 1990 .

[25]  S. Prasertsan,et al.  Heat pump dryer Part 1: Simulation of the models , 1996 .