Deterministic mixed lubrication modelling using roughness measurements in gear applications

The presence of surface roughness on the teeth of hardened and ground power transmission gears is an unavoidable consequence of their manufacture. The paper discusses the effect of surface roughness when the elastohydrodynamic lubricant film thickness developed between the gear tooth surfaces is small compared to the heights of the roughness features. The ratio of these quantities, called the Λ value, may be well below unity in typical applications. For such thin film conditions the moving roughness features cause the elastohydrodynamic contact between the gears to be highly transient in nature. Surface roughness features on the working surfaces of the gears move past each other during meshing and these asperity encounters are associated with extreme pressure perturbations, or with film breakdown and isolated asperity boundary lubrication events. The paper reviews approaches used to study this problem and describes a coupled approach to solving the elastic and hydrodynamic equations. This allows numerical solutions to be obtained for these extreme conditions so that transient contact events associated with mixed lubrication can be predicted in a unified numerical solution scheme. Typical results obtained from such an analysis are presented including surface fatigue modelling and contact strain energy calculations.

[1]  W. Findley.  A Theory for the Effect of Mean Stress on Fatigue of Metals Under Combined Torsion and Axial Load or Bending , 1959 .

[2]  J. Greenwood,et al.  The Contact of Two Nominally Flat Rough Surfaces , 1970 .

[3]  C. Arcoumanis,et al.  Mixed Lubrication Modelling of Newtonian and Shear Thinning Liquids in a Piston-Ring Configuration , 1997 .

[4]  Tian Tian,et al.  The Effects of Cylinder Liner Finish on Piston Ring-Pack Friction , 2004 .

[5]  Tomokazu Matake.  An Explanation on Fatigue Limit under Combined Stress , 1977 .

[6]  A. Fatemi,et al.  A CRITICAL PLANE APPROACH TO MULTIAXIAL FATIGUE DAMAGE INCLUDING OUT‐OF‐PHASE LOADING , 1988 .

[7]  J. Tripp.  Surface Roughness Effects in Hydrodynamic Lubrication: The Flow Factor Method , 1983 .

[8]  Henry Peredur Evans,et al.  Conditions for Scuffing Failure of Ground and Superfinished Steel Disks at High Sliding Speeds Using a Gas Turbine Engine Oil , 1995 .

[9]  H. Cheng,et al.  An Average Flow Model for Determining Effects of Three-Dimensional Roughness on Partial Hydrodynamic Lubrication , 1978 .

[10]  J. A. Greenwood,et al.  Waviness Amplitude Reduction in EHL Line Contacts Under Rolling-Sliding , 1998 .

[11]  Richard F. Salant,et al.  An Average Flow Model of Rough Surface Lubrication With Inter-Asperity Cavitation , 2001 .

[12]  Henry Peredur Evans,et al.  Elastohydrodynamic response of transverse ground gear teeth , 2002 .

[13]  H. P. Evans,et al.  Transient elastohydrodynamic point contact analysis using a new coupled differential deflection method Part 1: Theory and validation , 2003 .

[14]  J A Greenwood,et al.  The Behaviour of Transverse Roughness in EHL Contacts , 1994 .

[15]  C. Hooke,et al.  Surface roughness modification in elastohydrodynamic line contacts operating in the elastic piezoviscous regime , 1998 .

[16]  S. Timoshenko,et al.  Theory of elasticity , 1975 .

[17]  Henry Peredur Evans,et al.  Analysis of Mixed Lubrication Effects in Simulated Gear Tooth Contacts , 2005 .

[18]  H. P. Evans,et al.  Comparison of fatigue model results for rough surface elastohydrodynamic lubrication , 2008 .

[19]  H P Evans,et al.  Evaluation of deflection in semi-infinite bodies by a differential method , 2000 .

[20]  Dong Zhu,et al.  A Computer Program Package for the Prediction of EHL and Mixed Lubrication Characteristics, Friction, Subsurface Stresses and Flash Temperatures Based on Measured 3-D Surface Roughness , 2001 .

[21]  C J Hooke.  Engineering analysis of rough elastohydrodynamically lubricated contacts , 2009 .

[22]  Henry Peredur Evans,et al.  Elastohydrodynamic Lubrication Analysis of Gear Tooth Surfaces From Micropitting Tests , 2003 .

[23]  A. A. Lubrecht,et al.  An Engineering Tool for the Quantitative Prediction of General Roughness Deformation in EHL Contacts Based on Harmonic Waviness Attenuation , 2005 .

[24]  D. Zhu,et al.  On some aspects of numerical solutions of thin-film and mixed elastohydrodynamic lubrication , 2007 .

[25]  Dong Zhu,et al.  Mixed Lubrication Analyses by a Macro-Micro Approach and a Full-Scale Mixed EHL Model , 2004 .

[26]  T. Makino,et al.  Application of average flow model to thin film gas lubrication , 1993 .

[27]  A. Lubrecht,et al.  Amplitude Reduction of Waviness in Transient EHL Line Contacts , 1997 .

[28]  Dong Zhu,et al.  Pitting Life Prediction Based on a 3D Line Contact Mixed EHL Analysis and Subsurface von Mises Stress Calculation , 2009 .

[29]  C. Amzallag,et al.  Standardization of the rainflow counting method for fatigue analysis , 1994 .