On developing an optimal design procedure for a bimorph piezoelectric cantilever energy harvester under a predefined volume

Abstract A typical vibration harvester is tuned to operate at resonance in order to maximize the power output. There are many design parameter sets for tuning the harvester to a specific frequency, even for simple geometries. This work studies the impact of the geometrical parameters on the harvested power while keeping the resonance frequency constant in order to find the combination of the parameters that optimizes the power under a predefined volume. A bimorph piezoelectric cantilever is considered for the study. It consists of two piezoelectric layers and a middle non-piezoelectric layer and holds a tip mass. A theoretical model was derived to obtain the system parameters and the power as functions of the design parameters. Formulas for the optimal load resistance that provide maximum power capability at resonance and anti-resonance frequency were derived. The influence of the width on the power is studied, considering a constant mass ratio (between the tip mass and the mass of the beam). This keeps the resonance frequency constant while changing the width. The influence of the ratio between the thickness of the middle layer and that of the piezoelectric layer is also studied. It is assumed that the total thickness of the cantilever is constant and the middle layer has the same mechanical properties (elasticity and density) as the piezoelectric layer. This keeps the resonance frequency constant while changing the ratio between the thicknesses. Finally, the influence of increasing the free length as well as of increasing the mass ratio on the power is investigated. This is done by first, increasing each of them individually and secondly, by increasing each of them simultaneously while increasing the total thickness under the condition of maintaining a constant resonance frequency. Based on the analysis of these influences, recommendations as to how to maximize the geometrical parameters within the available volume and mass are presented.

[1]  Dennis Hohlfeld,et al.  Modeling and characterization of MEMS-based piezoelectric harvesting devices , 2010 .

[2]  Jens Twiefel,et al.  A Study on Bandwidth and Performance Limitations of Array Vibration Harvester Configurations , 2017 .

[3]  Hironao Okada,et al.  Design of piezoelectric MEMS cantilever for low-frequency vibration energy harvester , 2016 .

[4]  Qingfeng Meng,et al.  Analytical modeling and experimental verification of vibration-based piezoelectric bimorph beam with a tip-mass for power harvesting , 2013 .

[5]  J. Twiefel,et al.  Optimization of a Piezoelectric Bending Actuator for a Tactile Virtual Reality Display , 2015 .

[6]  J. Dugundji,et al.  Modeling and experimental verification of proof mass effects on vibration energy harvester performance , 2010 .

[7]  Nesbitt W. Hagood,et al.  Modelling of Piezoelectric Actuator Dynamics for Active Structural Control , 1990 .

[8]  Arpys Arevalo,et al.  Parametric Study of Polyimide – Lead Zirconate Titanate Thin Film Cantilivers for Transducer Applications , 2013 .

[9]  Yiannos Manoli,et al.  A self-adaptive energy harvesting system , 2016 .

[10]  L. E. Cross,et al.  Performance analysis of piezoelectric cantilever bending actuators , 1998 .

[11]  Brian L. Wardle,et al.  Optimal design of piezoelectric materials and devices for energy harvesting , 2013 .

[12]  Jens Twiefel,et al.  Model-based design of piezoelectric energy harvesting systems , 2006, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[13]  Atanas A. Popov,et al.  PARAMETRIC STUDY OF A CANTILEVERED PIEZOELECTRIC ENERGY HARVESTER , 2009 .

[14]  Jens Twiefel,et al.  Survey on broadband techniques for vibration energy harvesting , 2013 .

[15]  Daniel J. Inman,et al.  Estimation of Electric Charge Output for Piezoelectric Energy Harvesting , 2004 .

[16]  Mustafa Arafa,et al.  A self-tuning resonator for vibration energy harvesting , 2013 .

[17]  Walter Sextro,et al.  Analytical determination of characteristic frequencies and equivalent circuit parameters of a piezoelectric bimorph , 2012 .

[18]  Alperen Toprak,et al.  Piezoelectric energy harvesting: State-of-the-art and challenges , 2014 .

[19]  Andrés Vásquez Quintero,et al.  Design optimization of vibration energy harvesters fabricated by lamination of thinned bulk-PZT on polymeric substrates , 2014 .

[20]  R. B. Yates,et al.  Analysis Of A Micro-electric Generator For Microsystems , 1995, Proceedings of the International Solid-State Sensors and Actuators Conference - TRANSDUCERS '95.

[21]  V. Bedekar,et al.  Modeling, Simulation and Optimization of Piezoelectric Bimorph Transducer for Broadband Vibration Energy Harvesting , 2017 .

[22]  Noël E. Dutoit,et al.  Experimental Verification of Models for Microfabricated Piezoelectric Vibration Energy Harvesters , 2007 .

[23]  M. G. Prasad,et al.  Two-dimensional resonance frequency tuning approach for vibration-based energy harvesting , 2016 .