Modeling, validation, and performance of low-frequency piezoelectric energy harvesters

Analytical and finite element electromechanical models that take into account the fact that the piezoelectric sheet does not cover the whole substrate beam are developed. A linear analysis of the analytical model is performed to determine the optimal load resistance. The analytical and finite element models are validated with experimental measurements. The results show that the analytical model that takes into account the fact that the piezoelectric patch does not cover the whole beam predicts accurately the experimental measurements. The finite element results yield a slight discrepancy in the global frequency and a slight overestimation in the value of the harvested power at resonance. On the contrary, using an approximate analytical model based on mode shapes of the full covered beam leads to erroneous results and overestimation of the global frequency as well as the level of harvested power. In order to design enhanced piezoelectric energy harvesters that can generate energy at low-frequency excitations, further analysis is performed to investigate the effects of varying the length of the piezoelectric material on the natural frequency and the performance of the harvester. The results show that there is a compromise between the length of the piezoelectric material, the electrical load resistance, and the available excitation frequency. By quantifying this compromise, we optimize the performance of beam–mass systems to efficiently harvest energy from a specified low frequency of the ambient vibrations.

[1]  Daniel J. Inman,et al.  On the energy harvesting potential of piezoaeroelastic systems , 2010 .

[2]  Norman M. Wereley,et al.  Energy Harvesting Devices Using Macro-fiber Composite Materials , 2010 .

[3]  Abdessattar Abdelkefi,et al.  Modeling and performance analysis of cambered wing-based piezoaeroelastic energy harvesters , 2013 .

[4]  Abdessattar Abdelkefi,et al.  Design and performance of variable-shaped piezoelectric energy harvesters , 2014 .

[5]  Shadrach Roundy,et al.  On the Effectiveness of Vibration-based Energy Harvesting , 2005 .

[6]  Col John Dillard,et al.  MODELInG THE PERFORMAnCE , 2009 .

[7]  Muhammad R. Hajj,et al.  Energy harvesting from a multifrequency response of a tuned bending–torsion system , 2012 .

[8]  Daniel J. Inman,et al.  A Distributed Parameter Electromechanical Model for Cantilevered Piezoelectric Energy Harvesters , 2008 .

[9]  D. Inman,et al.  On Mechanical Modeling of Cantilevered Piezoelectric Vibration Energy Harvesters , 2008 .

[10]  Daniel J. Inman,et al.  Analytical Modeling and Experimental Verification of the Vibrations of the Zigzag Microstructure for Energy Harvesting , 2011 .

[11]  Daniel J. Inman,et al.  An experimentally validated bimorph cantilever model for piezoelectric energy harvesting from base excitations , 2009 .

[12]  Muhammad R. Hajj,et al.  Performance analysis of galloping-based piezoaeroelastic energy harvesters with different cross-section geometries , 2014 .

[13]  Mohammed F. Daqaq,et al.  On intentional introduction of stiffness nonlinearities for energy harvesting under white Gaussian excitations , 2012 .

[14]  Abdessattar Abdelkefi,et al.  An energy harvester using piezoelectric cantilever beams undergoing coupled bending–torsion vibrations , 2011 .

[15]  David Koo,et al.  Modeling the performance of a micromachined piezoelectric energy harvester , 2012 .

[16]  Ali H. Nayfeh,et al.  Sensitivity analysis of piezoaeroelastic energy harvesters , 2012 .

[17]  Sang-Gook Kim,et al.  DESIGN CONSIDERATIONS FOR MEMS-SCALE PIEZOELECTRIC MECHANICAL VIBRATION ENERGY HARVESTERS , 2005 .

[18]  Daniel J. Inman,et al.  Artificial piezoelectric grass for energy harvesting from turbulence-induced vibration , 2012 .

[19]  Paul K. Wright,et al.  A piezoelectric vibration based generator for wireless electronics , 2004 .

[20]  Alper Erturk,et al.  Enhanced aeroelastic energy harvesting by exploiting combined nonlinearities: theory and experiment , 2011 .

[21]  Ali H. Nayfeh,et al.  Modeling and analysis of piezoaeroelastic energy harvesters , 2012 .

[22]  Mohammed F. Daqaq,et al.  Electromechanical Modeling and Nonlinear Analysis of Axially Loaded Energy Harvesters , 2011 .

[23]  Norman M. Wereley,et al.  Performance Evaluation of Multi-tier Energy Harvesters Using Macro-fiber Composite Patches , 2009 .