Axial-flux PM starter/alternator machine with a novel mechanical device for extended flux weakening capabilities

In modern vehicles, the demand for on-board electric energy generation is rapidly growing in order to satisfy new requirements for passengers comfort and safety. This growth, which is predicted to reach 6 kW in the very next years, is forcing manufacturers to explore new solutions concerning the whole electrical system inside the vehicle. In particular, novel topologies of alternators are under research since the currently used Lundell type (claw-pole) alternator is reaching its power limits. In this paper an original torque dependant mechanical device is proposed in order to extend the speed range of an axial flux PM machine. This device displaces the rotors realizing a mechanical flux weakening with constant output power in generation. Simulations and experimental tests on a prototype realized in the lab are fully discussed.

[1]  J. G. Kassakian,et al.  Automotive electrical systems circa 2005 , 1996 .

[2]  D.J. Perreault,et al.  Automotive power generation and control , 2004, IEEE Transactions on Power Electronics.

[3]  Feng Liang,et al.  A vehicle electric power generation system with improved output power and efficiency , 1998, Conference Record of 1998 IEEE Industry Applications Conference. Thirty-Third IAS Annual Meeting (Cat. No.98CH36242).

[4]  T. Keim,et al.  Performance improvement of alternators with switched-mode rectifiers , 2004, IEEE Transactions on Energy Conversion.

[5]  David J. Perreault,et al.  Performance improvement of alternators with switched-mode rectifiers , 2003, IEEE 34th Annual Conference on Power Electronics Specialist, 2003. PESC '03..

[6]  Bruno Lequesne,et al.  Design and testing of a belt-driven induction starter-generator , 2002 .

[7]  N. Ertugrul,et al.  Inverterless high-power interior permanent-magnet automotive alternator , 2004, IEEE Transactions on Industry Applications.

[8]  Nady Boules,et al.  A high-efficiency, high power generation system for automobiles , 1995 .

[9]  J.M. Miller,et al.  Starter-alternator for hybrid electric vehicle: comparison of induction and variable reluctance machines and drives , 1998, Conference Record of 1998 IEEE Industry Applications Conference. Thirty-Third IAS Annual Meeting (Cat. No.98CH36242).

[10]  T.M. Jahns,et al.  Investigation of interior permanent magnet offset-coupled automotive integrated starter/alternator , 2001, Conference Record of the 2001 IEEE Industry Applications Conference. 36th IAS Annual Meeting (Cat. No.01CH37248).

[11]  F. Crescimbini,et al.  High-efficiency low-volume starter/alternator for automotive applications , 2000, Conference Record of the 2000 IEEE Industry Applications Conference. Thirty-Fifth IAS Annual Meeting and World Conference on Industrial Applications of Electrical Energy (Cat. No.00CH37129).

[12]  F. Crescimbini,et al.  Permanent-magnet, direct-drive, starter/alternator machine with weakened flux linkage for constant-power operation over extremely wide speed range , 2001, Conference Record of the 2001 IEEE Industry Applications Conference. 36th IAS Annual Meeting (Cat. No.01CH37248).

[13]  John Michael Miller,et al.  A control scheme to maximize output power of a synchronous alternator in a vehicle electrical power generation system , 1996, IAS '96. Conference Record of the 1996 IEEE Industry Applications Conference Thirty-First IAS Annual Meeting.

[14]  M. Gabsi,et al.  A switched reluctance machine for a car starter-alternator system , 2001, IEMDC 2001. IEEE International Electric Machines and Drives Conference (Cat. No.01EX485).

[15]  Shigeo Morimoto,et al.  Advantages of IPMSM with adjustable PM armature flux linkage in efficiency improvement and operating range extension , 2002, Proceedings of the Power Conversion Conference-Osaka 2002 (Cat. No.02TH8579).