Topology optimization for additive manufacturing: Accounting for overhang limitations using a virtual skeleton

Abstract This article proposes a new method for reducing the amount of support material required for 3-D printing of complex designs generated by topology optimization. This procedure relies on solving sequentially two structural optimization problems – the first on a discrete truss-based model and the second on a continuum-based model. In the optimization of the discrete model, the maximum overhang limitation is imposed based on geometrical parameters. The optimized discrete pattern is then projected on to the continuum so that it influences the material distribution in the continuum optimization. The method is explained and investigated on a set of test cases in 2-D and subsequently demonstrated on examples in 3-D. Numerical results indicate that the designs obtained by this approach exhibit improved printability as they have fewer overhanging features. In some cases, practically no supporting material will be required for printing the optimized design.

[1]  Ramana V. Grandhi,et al.  A survey of structural and multidisciplinary continuum topology optimization: post 2000 , 2014 .

[2]  James K. Guest,et al.  Topology optimization considering overhang constraints: Eliminating sacrificial support material in additive manufacturing through design , 2016 .

[3]  O. Sigmund,et al.  Topology optimisation for natural convection problems , 2014, 1408.2102.

[4]  I. Ashcroft,et al.  Topology Optimization for Additive Manufacturing , 2011 .

[5]  Matthijs Langelaar,et al.  An additive manufacturing filter for topology optimization of print-ready designs , 2016, Structural and Multidisciplinary Optimization.

[6]  Anders Klarbring,et al.  An Introduction to Structural Optimization , 2008 .

[7]  A. Clausen.  Topology Optimization for Additive Manufacturing , 2016 .

[8]  R. Poprawe,et al.  Laser additive manufacturing of metallic components: materials, processes and mechanisms , 2012 .

[9]  Kaufui Wong,et al.  A Review of Additive Manufacturing , 2012 .

[10]  James K. Guest,et al.  Achieving minimum length scale in topology optimization using nodal design variables and projection functions , 2004 .

[11]  Matteo Bruggi,et al.  Topology optimization for thermal insulation: an application to building engineering , 2011 .

[12]  K. Svanberg.  The method of moving asymptotes—a new method for structural optimization , 1987 .

[13]  Harvey J. Greenberg,et al.  Automatic design of optimal structures , 1964 .

[14]  A. Gibb,et al.  Hardened properties of high-performance printing concrete , 2012 .

[15]  Yunqing Zhang,et al.  Manufacturing- and machining-based topology optimization , 2006 .

[16]  A. Bandyopadhyay,et al.  Bone tissue engineering using 3D printing , 2013 .

[17]  William E. Frazier,et al.  Metal Additive Manufacturing: A Review , 2014, Journal of Materials Engineering and Performance.

[18]  Matthijs Langelaar,et al.  Topology optimization of 3D self-supporting structures for additive manufacturing , 2016 .

[19]  Jian Zhang,et al.  A new topology optimization approach based on Moving Morphable Components (MMC) and the ersatz material model , 2016 .

[20]  S. Torquato,et al.  Design of materials with extreme thermal expansion using a three-phase topology optimization method , 1997 .

[21]  Hod Lipson,et al.  Fabricated: The New World of 3D Printing , 2013 .

[22]  Christopher B. Williams,et al.  Topology Optimization for Additive Manufacturing: Considering Maximum Overhang Constraint , 2014 .

[23]  Oded Amir,et al.  A topology optimization procedure for reinforced concrete structures , 2013 .

[24]  Mu Zhu,et al.  Casting and Milling Restrictions in Topology Optimization via Projection-Based Algorithms , 2012, DAC 2012.

[25]  M. Bendsøe,et al.  Generating optimal topologies in structural design using a homogenization method , 1988 .

[26]  A. M. Driessen,et al.  Overhang constraint in topology optimisation for additive manufacturing: a density gradient based approach , 2016 .

[27]  G. Paulino,et al.  GRAND3 — Ground structure based topology optimization for arbitrary 3D domains using MATLAB , 2015, Structural and Multidisciplinary Optimization.

[28]  B. Bourdin.  Filters in topology optimization , 2001 .

[29]  Zhenyu Liu,et al.  Topology Optimization Theory for Laminar Flow , 2018 .

[30]  Boyan Stefanov Lazarov,et al.  On multigrid-CG for efficient topology optimization , 2013, Structural and Multidisciplinary Optimization.

[31]  O. Sigmund,et al.  Topology optimization approaches , 2013, Structural and Multidisciplinary Optimization.

[32]  Milan Sonka,et al.  Image Processing, Analysis and Machine Vision , 1993, Springer US.

[33]  M. Bendsøe,et al.  Topology Optimization: "Theory, Methods, And Applications" , 2011 .

[34]  Anders Clausen,et al.  Efficient topology optimization in MATLAB using 88 lines of code , 2011 .

[35]  Daniel Thomas.  The development of design rules for selective laser melting , 2009 .

[36]  Xiaoping Qian,et al.  Undercut and overhang angle control in topology optimization: A density gradient based integral approach , 2017 .

[37]  T. E. Bruns,et al.  Topology optimization of non-linear elastic structures and compliant mechanisms , 2001 .

[38]  D. Tortorelli,et al.  A geometry projection method for continuum-based topology optimization with discrete elements , 2015 .

[39]  M. Bendsøe.  Optimal shape design as a material distribution problem , 1989 .

[40]  Martin Leary,et al.  Optimal topology for additive manufacture: A method for enabling additive manufacture of support-free optimal structures , 2014 .

[41]  Milan Sonka,et al.  Image pre-processing , 1993 .

[42]  T. E. Bruns,et al.  Topology optimization of convection-dominated, steady-state heat transfer problems , 2007 .

[43]  James K. Guest,et al.  Reinforced Concrete Force Visualization and Design Using Bilinear Truss-Continuum Topology Optimization , 2013 .