Derivation of parameters for a two compartment population balance model of Wurster fluidised bed granulation

Abstract A common technology for granulation processes is the fluidised bed bottom-spray. This technology can be improved by the use of an internal riser, a so-called Wurster tube. The internal riser has advantages in terms of system stability and enhanced control of particle growth. To mathematically describe the particle growth in such an equipment population balance models (PBM) are applied. These models can be extended by subdivision into a spray compartment and a drying compartment. Important parameters in the compartment models are the compartment size and the particle residence time. In this work, residence time distributions in the riser spray compartment are obtained by a simple gas–particle flow model. The model validity is proven by Particle Image Velocimetry (PIV) and image analysis measurements in a flat test facility. By using an extended PBM it is shown that the particle size distribution (PSD) of the product is not only influenced by the existence of two compartments, but also by the particle size dependent residence time in the spray compartment, which causes additional broadening and skewness. The influence of riser design on particle motion, circulation patterns and product PSD is discussed on the basis of experimental and computational results.

[1]  R. Clift,et al.  Motion of entrained particles in gas streams , 1971 .

[2]  J. Kuipers,et al.  Hydrodynamic modelling of dense gas-fluidised beds: comparison and validation of 3D discrete particle and continuum models , 2004 .

[3]  Dominic F. Sherony.  A model of surface renewal with application to fluid bed coating of particles , 1981 .

[4]  G. Micale,et al.  Analysis of the bubbling behaviour of 2D gas solid fluidized beds: Part I. Digital image analysis technique , 2008 .

[5]  Teklay Weldeabzgi Asegehegn,et al.  Investigation of bubble behavior in fluidized beds with and without immersed horizontal tubes using a digital image analysis technique , 2011 .

[6]  Ng Niels Deen,et al.  Validation of a Discrete Particle Model in a 2D Spout-Fluid Bed Using Non-Intrusive Optical Measuring Techniques , 2008 .

[7]  K. Cronin,et al.  Modelling of particle motion in an internal re-circulatory fluidized bed , 2010 .

[8]  Martin van Sint Annaland,et al.  Investigation into the hydrodynamics of gas–solid fluidized beds using particle image velocimetry coupled with digital image analysis , 2008 .

[9]  Mirko Peglow,et al.  Prozessdynamik der Wirbelschichtgranulierung , 2011 .

[10]  Markus Raffel,et al.  Particle Image Velocimetry: A Practical Guide , 2002 .

[11]  Stefan Heinrich,et al.  Moisture Distribution in Fluidized Beds with Liquid Injection , 2011 .

[12]  Stefan Heinrich,et al.  An experimental study of the effect of collision properties on spout fluidized bed dynamics , 2011 .

[13]  Lian X. Liu,et al.  Coating mass distribution from a spouted bed seed coater: Experimental and modelling studies , 1993 .

[14]  Piotr Wnukowski,et al.  Modelling of the three-domain fluidized-bed particulate coating process , 1997 .

[15]  R. Turton,et al.  Nonuniformity of particle coating on a size distribution of particles in a fluidized bed coater , 2000 .

[16]  Jam Hans Kuipers,et al.  Mixing and segregation in a bidisperse gas-solid fluidized bed: a numerical and experimental study , 2004 .

[17]  C. Wen.  Mechanics of Fluidization , 1966 .

[18]  Jürgen Kompenhans,et al.  Particle Image Velocimetry - A Practical Guide (2nd Edition) , 2007 .

[19]  F. Johnsson,et al.  Digital image analysis of hydrodynamics two-dimensional bubbling fluidized beds , 2004 .

[20]  F. Taghipour,et al.  Experimental and computational study of gas¿solid fluidized bed hydrodynamics , 2005 .

[21]  David Parker,et al.  Numerical and experimental study on multiple-spout fluidized beds , 2011 .

[22]  Fredrik Setterwall,et al.  The coating of particles in a fluidized bed (residence time distribution in a system of two coupled perfect mixers) , 1989 .

[23]  Jam Hans Kuipers,et al.  Flow regimes in a spout-fluid bed : A combined experimental and simulation study , 2005 .

[24]  S. Sánchez-Delgado,et al.  Comparison between two-fluid model simulations and particle image analysis & velocimetry (PIV) results for a two-dimensional gas–solid fluidized bed , 2011 .

[25]  D. Wurster,et al.  Air-suspension technique of coating drug particles; a preliminary report. , 1959, Journal of the American Pharmaceutical Association. American Pharmaceutical Association.

[26]  Ng Niels Deen,et al.  Characterization of the pneumatic behavior of a novel spouted bed apparatus , 2008 .

[27]  J. Westerweel.  Fundamentals of digital particle image velocimetry , 1997 .

[28]  S. Heinrich,et al.  Analysis of the start-up process in continuous fluidized bed spray granulation by population balance modelling , 2002 .