Reactivation and remaking of calcium aluminate pellets for CO2 capture

Abstract CaO-based pellets supported with aluminate cements show superior performance in carbonation/calcination cycles for high-temperature CO 2 capture. However, like other CaO-based sorbents, their CO 2 carrying activity is reduced after increasing numbers of cycles under high-temperature, high-CO 2 concentration conditions. In this work the feasibility of their reactivation by steam or water and remaking (reshaping) was investigated. The pellets, prepared from three limestones, Cadomin and Havelock (Canada) and Katowice (Poland, Upper Silesia), were tested in a thermogravimetric analyzer (TGA). The cycles were performed under realistic CO 2 capture conditions, which included calcination in 100% CO 2 at temperatures up to 950 °C. Typically, after 30 cycles, samples were hydrated for 5 min with saturated steam at 100 °C in a laboratory steam reactor (SR). Moreover, larger amounts of pellets were cycled in a tube furnace (TF), hydrated with water and reshaped, and tested to determine their CO 2 capture activity in the TGA. It was found that, after the hydration stage, pellets recovered their activity, and more interestingly, pellets that had experienced a longer series of cycles responded more favorably to reactivation. Moreover, it was found that conversion of pellets increased after about 70 cycles (23%), reaching 33% by about cycle 210, with no reactivation step. Scanning electron microscope (SEM) analyses showed that the morphology of the low-porosity shell formed at the pellet surface during cycles, which limits conversion, was eliminated after a short period (5 min) of steam hydration. The nitrogen physisorption analyses (BET, BJH) of reshaped spent pellets from cycles in the TF confirmed that sorbent surface area and pore size distribution were similar to those of the original pellets. The main alumina compound in remade pellets as determined by XRD was mayenite (Ca 12 Al 14 O 33 ). These results showed that, with periodic hydration/remaking steps, pellets can be used for extended times in CO 2 looping cycles, regardless of capture/regeneration conditions.

[1]  H. Herzog.  Peer Reviewed: What Future for Carbon Capture and Sequestration? , 2001 .

[2]  J. S. Dennis,et al.  The rate and extent of uptake of CO2 by a synthetic, CaO-containing sorbent , 2009 .

[3]  Mónica Alonso,et al.  Sulfation of CaO Particles in a Carbonation/Calcination Loop to Capture CO2 , 2008 .

[4]  Paul S. Fennell,et al.  The calcium looping cycle for large-scale CO2 capture , 2010 .

[5]  Xiaoping Chen,et al.  Cyclic CO2 capture behavior of KMnO4-doped CaO-based sorbent , 2010 .

[6]  Vasilije Manovic,et al.  Long-Term Behavior of CaO-Based Pellets Supported by Calcium Aluminate Cements in a Long Series of CO2 Capture Cycles , 2009 .

[7]  Vasilije Manovic,et al.  Improvement of CaO-based sorbent performance for CO2 looping cycles , 2009 .

[8]  John R. Grace,et al.  The effect of CaO sintering on cyclic CO2 capture in energy systems , 2007 .

[9]  Angeliki A. Lemonidou,et al.  Parametric Study of the CaO−Ca12Al14O33 Synthesis with Respect to High CO2 Sorption Capacity and Stability on Multicycle Operation , 2008 .

[10]  L. Romeo,et al.  Integration of Carbonate CO2 Capture Cycle and Coal-Fired Power Plants. A Comparative Study for Different Sorbents , 2010 .

[11]  V. Manović,et al.  SO2 retention by reactivated CaO-based sorbent from multiple CO2 capture cycles. , 2007, Environmental science & technology.

[12]  Vasilije Manovic,et al.  CO2 Carrying Behavior of Calcium Aluminate Pellets under High-Temperature/ High-CO2 Concentration Calcination Conditions , 2010 .

[13]  J. C. Abanades,et al.  Cost structure of a postcombustion CO2 capture system using CaO. , 2007, Environmental science & technology.

[14]  Robin W. Hughes,et al.  Ca-based sorbent looping combustion for CO2 capture in pilot-scale dual fluidized beds , 2008 .

[15]  J. Woods,et al.  Pacification of high calcic residues using carbon dioxide , 2000 .

[16]  Juan Carlos Abanades,et al.  Economics of CO2 Capture Using the Calcium Cycle with a Pressurized Fluidized Bed Combustor , 2007 .

[17]  P. Fennell,et al.  Regeneration of sintered limestone sorbents for the sequestration of CO2 from combustion and other systems , 2007 .

[18]  Vasilije Manovic,et al.  Competition of sulphation and carbonation reactions during looping cycles for CO2 capture by CaO-based sorbents. , 2010, The journal of physical chemistry. A.

[19]  Himanshu Gupta,et al.  Kinetics and Structural Characterization of Calcium-Based Sorbents Calcined under Subatmospheric Conditions for the High-Temperature CO2 Capture Process , 2007 .

[20]  Edward S. Rubin,et al.  Evaluation of potential cost reductions from improved amine-based CO2 capture systems , 2006 .

[21]  Vasilije Manovic,et al.  Steam reactivation of spent CaO-based sorbent for multiple CO2 capture cycles. , 2007, Environmental science & technology.

[22]  C. Müller,et al.  Performance of a Novel Synthetic Ca-Based Solid Sorbent Suitable for Desulfurizing Flue Gases in a Fluidized Bed , 2009, Industrial & Engineering Chemistry Research.

[23]  Jon Gibbins,et al.  Initial evaluation of the impact of post-combustion capture of carbon dioxide on supercritical pulverised coal power plant part load performance , 2007 .

[24]  V. Manović,et al.  Sequential SO2/CO2 capture enhanced by steam reactivation of a CaO-based sorbent , 2008 .

[25]  A. I. Lysikov,et al.  Change of CO2 Carrying Capacity of CaO in Isothermal Recarbonation−Decomposition Cycles , 2007 .

[26]  J. C. Abanades,et al.  Conversion Limits in the Reaction of CO2 with Lime , 2003 .

[27]  Stefan Bachu,et al.  CO2 storage in geological media: Role, means, status and barriers to deployment , 2008 .

[28]  E. Anthony.  Solid looping cycles: A new technology for coal conversion , 2008 .

[29]  E. J. Anthony,et al.  Fluidized bed combustion systems integrating CO2 capture with CaO. , 2005, Environmental science & technology.

[30]  Vasilije Manovic,et al.  Thermal activation of CaO-based sorbent and self-reactivation during CO2 capture looping cycles. , 2008, Environmental science & technology.

[31]  Luis M. Romeo,et al.  Economical assessment of competitive enhanced limestones for CO2 capture cycles in power plants , 2009 .

[32]  D. Harrison.  Sorption-Enhanced Hydrogen Production: A Review , 2008 .

[33]  T. Shimizu,et al.  A twin fluid-bed reactor for removal of CO2 from combustion processes , 1999 .

[34]  L. Romeo,et al.  Optimizing make-up flow in a CO2 capture system using CaO , 2009 .

[35]  E. J. Anthony,et al.  A study on the activity of CaO-based sorbents for capturing CO2 in clean energy processes , 2010 .

[36]  Ningsheng Cai,et al.  Synthesis, experimental studies, and analysis of a new calcium-based carbon dioxide absorbent , 2005 .

[37]  B. R. Stanmore,et al.  Review—calcination and carbonation of limestone during thermal cycling for CO2 sequestration , 2005 .

[38]  Vasilije Manovic,et al.  CaO-based pellets supported by calcium aluminate cements for high-temperature CO2 capture. , 2009, Environmental science & technology.

[39]  Nicholas H. Florin,et al.  Enhanced hydrogen production from biomass with in situ carbon dioxide capture using calcium oxide sorbents , 2008 .