Analysis of influencing factors of heat extraction from enhanced geothermal systems considering water losses

A three-dimensional thermal-hydrologic model considering water losses was developed to simulate heat extraction from an enhanced geothermal system (EGS), consisting of an injection well, a production well, a reservoir and the surrounding formation. The model was verified by application to Fenton Hill EGS. Based on the model, the influences of some factors on heat extraction were analyzed. As surrounding formation permeability increases, there are more water losses from the reservoir to the surrounding formation, leading to decreased heat extraction rate. When the two wells approach the edge of the reservoir, heat extraction is restrained, indicating that the two wells should be located about 20–25 m from the edge of the reservoir. Enlarged reservoir volume would not efficiently enhance heat extraction with fixed well layout, suggesting that well layout should be further optimized. Optimized open-hole length is equal to vertical reservoir dimension. Lower production pressure enhances heat extraction, resulting from increased production flow rate and decreased water loss rate. For each factor, it is concluded that thermal breakthrough time mainly depends on production flow rate and water loss rate, showing the important effect of water losses. The results of this paper can offer some suggestions to optimize the EGS performance.

[1]  Jian Hu,et al.  Numerical simulation of heat production potential from hot dry rock by water circulating through a novel single vertical fracture at Desert Peak geothermal field , 2013 .

[2]  Jiliang Chen,et al.  Designing multi-well layout for enhanced geothermal system to better exploit hot dry rock geothermal energy , 2015 .

[3]  Corné Kreemer,et al.  Active deformation in eastern Indonesia and the Philippines from GPS and seismicity data , 2000 .

[4]  Roland N. Horne,et al.  Optimization of injection scheduling in fractured geothermal reservoirs , 2013 .

[5]  Carlos E. Romero,et al.  Heat mining assessment for geothermal reservoirs in Mexico using supercritical CO2 injection , 2016 .

[6]  A. Ghassemi,et al.  A three-dimensional thermo-poroelastic model for fracture response to injection/extraction in enhanc , 2011 .

[7]  Wen-Long Cheng,et al.  A novel analytical transient heat-conduction time function for heat transfer in steam injection well , 2011 .

[8]  K. Pruess.  On production behavior of enhanced geothermal systems with CO2 as working fluid , 2008 .

[9]  Nasser Khalili,et al.  A thermo-hydro-mechanical coupled model in local thermal non-equilibrium for fractured HDR reservoir with double porosity , 2012 .

[10]  Tsutomu Yamaguchi,et al.  The Hijiori Hot Dry Rock test site, Japan: Evaluation and optimization of heat extraction from a two-layered reservoir , 2008 .

[11]  M. Kubik.  The Future of Geothermal Energy , 2006 .

[12]  Olaf Kolditz,et al.  Uncertainty analysis of thermo-hydro-mechanical coupled processes in heterogeneous porous media , 2010 .

[13]  T. Hashida,et al.  A simple 3-D thermoelastic model for assessment of the long-term performance of the Hijiori deep geothermal reservoir , 2014 .

[14]  M. Nathenson,et al.  The dependence of permeability on effective stress from flow tests at hot dry rock reservoirs at Rosemanowes (Cornwall) and Fenton Hill (New Mexico) , 1999 .

[15]  Wen-Long Cheng,et al.  Evaluation of working fluids for geothermal power generation from abandoned oil wells , 2014 .

[16]  D. Tritton,et al.  Physical Fluid Dynamics , 1977 .

[17]  Pei-Xue Jiang,et al.  System thermodynamic performance comparison of CO2-EGS and water-EGS systems , 2013 .

[18]  Ki-Bok Min,et al.  Determination of optimum parameters of doublet system in a horizontally fractured geothermal reservoir , 2012 .

[19]  Feng Luo,et al.  Numerical investigation of fluid flow and heat transfer in a doublet enhanced geothermal system with CO2 as the working fluid (CO2–EGS) , 2014 .

[20]  Tsutomu Yamaguchi,et al.  Fluid circulation and heat extraction from engineered geothermal reservoirs , 1999 .

[21]  Sadiq J. Zarrouk,et al.  Numerical model of the Habanero geothermal reservoir, Australia , 2015 .

[22]  Yong‐Le Nian,et al.  Studies on geothermal power generation using abandoned oil wells , 2013 .

[23]  Ghazal Izadi,et al.  The influence of thermal-hydraulic-mechanical- and chemical effects on the evolution of permeability, seismicity and heat production in geothermal reservoirs , 2015 .

[24]  Frank P. Incropera,et al.  Fundamentals of Heat and Mass Transfer , 1981 .

[25]  Kimio Watanabe,et al.  A three‐dimensional stochastic rock mechanics model of engineered geothermal systems in fractured crystalline rock , 2000 .

[26]  S. Haaland.  Simple and Explicit Formulas for the Friction Factor in Turbulent Pipe Flow , 1983 .

[27]  P. Kruger,et al.  Pre-test estimates of temperature decline for the LANL Fenton Hill Long-Term Flow Test , 1992 .

[28]  F. Jiang,et al.  A three-dimensional transient model for EGS subsurface thermo-hydraulic process , 2014 .

[29]  Joshua Taron,et al.  Numerical simulation of thermal-hydrologic-mechanical-chemical processes in deformable, fractured porous media , 2009 .

[30]  Joshua Taron,et al.  Thermal–hydrologic–mechanical–chemical processes in the evolution of engineered geothermal reservoirs , 2009 .

[31]  S. McKenna,et al.  ANALYSIS OF THE EFFECTS OF HETEROGENEITY ON HEAT EXTRACTION IN AN EGS REPRESENTED WITH THE CONTINUUM FRACTURE MODEL , 2012 .

[32]  Ramesh K. Agarwal,et al.  Simulation and optimization of enhanced geothermal systems using CO2 as a working fluid , 2015 .

[33]  T. Hashida,et al.  A 3-D water/rock chemical interaction model for prediction of HDR/HWR geothermal reservoir performance , 2002 .