Experimental and theoretical investigation of gas–liquid flow pressure drop across rupture discs

Abstract Experiments of air–water two-phase flow pressure drop through rupture discs have been carried out. The tested rupture discs of DN 25 and DN 40 are made of graphite with and without vacuum support. The experiments were performed under the following conditions of two-phase parameters; mass flux from 2000 up to 4000 kg/m2 s, quality from 1 to 20% and system pressure from 3 to 7 bar. The results demonstrate that the effect of the above-mentioned parameters is very significant at high ranges of mass flow quality, due to the increasing of two-phase flow resistance, energy dissipations, friction losses and interaction of the two phases. Based on the presented experimental results and the data published in the literature, new correlation has been developed to calculate the two-phase pressure across rupture discs. The model includes the relevant primary influencing parameter, fit the data well, and is sufficiency accurate for engineering purposes. The reproductive accuracy of the proposed model and the statistical comparison, based on about 1000 measured data in the literature, demonstrated that the proposed model is the best overall agreement with the data. The standard deviation of the data is less than 10%. The results reported enable practical designs with standard products and optimization of the geometry of the rupture discs installed in nuclear reactors.

[1]  Akira Inoue,et al.  Flow Behavior and Pressure Drop of Two-Phase Flow through C-Shaped Bend in Vertical Plane, (I) , 2012 .

[2]  S. L. Smith.  Void Fractions in Two-Phase Flow: A Correlation Based upon an Equal Velocity Head Model , 1969 .

[3]  R. J. Moffat,et al.  Contributions to the Theory of Single-Sample Uncertainty Analysis , 1982 .

[4]  M. Q. Al-Odat,et al.  Two-phase flow resistance in flexible metal hoses , 2008 .

[5]  J. Thome,et al.  Convective Boiling and Condensation , 1972 .

[6]  L. Raimondi.  Rigorous Calculation of Critical Flow Conditions for Pressure Safety Devices , 2007 .

[7]  M. Al-Shannag,et al.  Gas-liquid pressure drop in vertical internally wavy 90° bend , 2009 .

[8]  Ron Darby,et al.  On two-phase frozen and flashing flows in safety relief valuesRecommended calculation method and the proper use of the discharge coefficient , 2004 .

[9]  D. Chisholm,et al.  Pressure gradients due to friction during the flow of evaporating two-phase mixtures in smooth tubes and channels , 1973 .

[10]  Api Recommended Practice.  Guide for Pressure-Relieving and Depressuring Systems , 1997 .

[11]  Lutz Friedel,et al.  Prediction of Single‐ and Two‐Phase Flow Contraction through a Sharp‐Edged Short Orifice , 1999 .

[12]  Kensuke Usui,et al.  Flow Behavior and Pressure Drop of Two-Phase Flow through C-Shaped Bend in Vertical Plane, (II): Downward Flow , 1980 .

[13]  L. Friedel.  Improved Friction Pressure Drop Correlation for Horizontal and Vertical Two-Phase Pipe Flow , 1979 .

[14]  J. P. Holman,et al.  Experimental methods for engineers , 1971 .

[15]  Lutz Friedel,et al.  Reproductive accuracy of selected void fraction correlations for horizontal and vertical upflow , 1998 .

[16]  L. Friedel,et al.  Two-phase pressure drop across sudden contractions in duct areas , 1997 .

[17]  B. Shannak,et al.  Frictional pressure drop of gas liquid two-phase flow in pipes , 2008 .

[18]  Shannak Benbella.  Mixture loss coefficient of safety valves used in nuclear plants , 2009 .

[19]  H. Müller-Steinhagen,et al.  A simple friction pressure drop correlation for two-phase flow in pipes , 1986 .

[20]  Ron Darby,et al.  On two-phase frozen and flashing flows in safety relief values , 2004 .

[21]  K. Wehrstedt,et al.  Investigation of the explosive hazard of mixtures containing hydrogen peroxide and different alcohols. , 2004, Journal of Hazardous Materials.