Possibility of using PCMs in temperature control and performance enhancements of free stand and building integrated PV modules

Abstract Recently, phase change materials (PCMs) are suggested for the temperature control and the performance enhancement of PV modules. However, the thermal conductivity of the PCMs is very low and integrating the PV with PCM can adversely affect its performance. In the present work, the effectiveness of using PCM in thermal regulation and efficiency enhancement of free stand and building integrated PV modules are investigated. Four different PV modules; free stand, building integrated, PCM integrated, and Al2O3 nanoparticles enhanced PCM integrated are experimentally investigated. Temperatures distributions, open-circuit voltage, short-circuit current, output power and the efficiency of the modules were recorded and analyzed. The results show that (i) integrating the PV module to the building wall dramatically rise the temperature of the module where the daily maximum temperature increased from 50 °C to 75 °C, (ii) integrating the free stand module with PCM box can adversely affect its performance where the maximum daily temperature increased from 50 °C to 62 °C and adding nanoparticles to the PCM can improve the performance where the temperature is reduced to 59 °C, and (iii) integrating the building integrated PV module with PCM box enhances its daily average efficiency by 7.1% and the enhancement ratio increases to 14.2 by improving the thermal conductivity of the PCM by adding 2% Al2O3 nanoparticles.

[1]  Earle A. Wilson.  Theoretical and operational thermal performance of a ‘wet’ crystalline silicon PV module under Jamaican conditions , 2009 .

[2]  Gilles Fraisse,et al.  Energy performance of water hybrid PV/T collectors applied to combisystems of Direct Solar Floor type , 2007 .

[3]  B. Karlsson,et al.  Low-concentrating water-cooled PV-thermal hybrid systems for high latitudes , 2002, Conference Record of the Twenty-Ninth IEEE Photovoltaic Specialists Conference, 2002..

[4]  Philip C. Eames,et al.  Comparison of a Small Scale 3-d PCM Thermal Control Model with a Validated 2-d PCM Thermal Control Model , 2006 .

[5]  Pascal Henry Biwole,et al.  Improving the Performance of Solar Panels by the Use of Phase-Change Materials , 2011 .

[6]  Harald Rogaß,et al.  Photovoltaic Module with Latent Heat-Storage-Collector , 1998 .

[7]  M. J. Huang,et al.  Chapter 454 – The Application of Computational Fluid Dynamics to Predict the Performance of Phase Change Materials for Control of Photovoltaic Cell Temperature in Buildings , 2000 .

[8]  Pushpito Kumar Ghosh,et al.  Self regulation of photovoltaic module temperature in V-trough using a metal–wax composite phase change matrix , 2011 .

[9]  Brian Norton,et al.  Phase change materials for limiting temperature rise in building integrated photovoltaics , 2006 .

[10]  Alain Sommier,et al.  Thermal management of electronic devices using carbon foam and PCM/nano-composite , 2015 .

[11]  Brian Norton,et al.  Characterization of phase change materials for thermal control of photovoltaics using Differential Scanning Calorimetry and Temperature History Method , 2014 .

[12]  Xingxing Zhang,et al.  Review of R&D progress and practical application of the solar photovoltaic/thermal (PV/T) technologies. , 2012 .

[13]  S. Nada,et al.  Numerical investigations of using carbon foam/PCM/Nano carbon tubes composites in thermal management of electronic equipment , 2015 .

[14]  Hongxing Yang,et al.  Thermal regulation of photovoltaic cladding , 1997 .

[15]  W. G. Anderson,et al.  Heat pipe cooling of concentrating photovoltaic cells , 2008, 2008 33rd IEEE Photovoltaic Specialists Conference.

[16]  Ji Jie,et al.  A numerical and experimental study on a heat pipe PV/T system , 2011 .

[17]  Christopher J. Smith,et al.  Global analysis of photovoltaic energy output enhanced by phase change material cooling , 2014 .

[18]  Zahari Ibarahim,et al.  A validated model of naturally ventilated PV cladding , 2000 .

[19]  S. Krauter.  Increased electrical yield via water flow over the front of photovoltaic panels , 2004 .

[20]  K. Steemers,et al.  Design and overall energy performance of a ventilated photovoltaic façade , 2007 .

[21]  Brian Norton,et al.  The Effect of Phase Change Material Crystalline Segregation on the Building Integrated Photovoltaic System Thermal Performance , 2008 .

[22]  Y. Tripanagnostopoulos,et al.  Hybrid photovoltaic/thermal solar systems , 2002 .

[23]  Philip C. Eames,et al.  Natural convection in an internally finned phase change material heat sink for the thermal management of photovoltaics , 2011 .

[24]  Subbu Sethuvenkatraman,et al.  Energetic evaluation of thermal energy storage options for high efficiency solar cooling systems , 2017 .

[25]  M. J. Huang,et al.  The effect of using two PCMs on the thermal regulation performance of BIPV systems , 2009 .

[26]  Mats Sandberg,et al.  Design procedure for cooling ducts to minimise efficiency loss due to temperature rise in PV arrays , 2006 .

[27]  R. Crook,et al.  Energy balance model of combined photovoltaic solar-thermal system incorporating phase change material , 2011 .

[28]  Brian Norton,et al.  Evaluation of phase change materials for thermal regulation enhancement of building integrated photovoltaics , 2010 .

[29]  Rolf Hanitsch,et al.  Combined photovoltaic and solar thermal systems for facade integration and building insulation , 1999 .

[30]  Christophe Menezo,et al.  Experimental natural convection on vertical surfaces for building integrated photovoltaic (BIPV) applications , 2008 .