A novel approach in S-shaped input design for higher vibration reduction

This paper presents development and implementation of a novel approach to produce an s-shaped command with higher residual vibration.  In this work, a three dimensional gantry crane is considered where a complete nonlinear mathematical model of a laboratory crane with variable cable length is simulated. A distributed delay zero vibration shaper based approach is proposed to produce an s-curved command. The effectiveness of the shaped command is examined through simulations using the nonlinear model and experiments on the laboratory crane. Simulation and experimental results show that the proposed scheme resulted in lower overall sways for rail and trolley of the crane when compared to a conventional s-shaped signal.

[1]  William Singhose,et al.  Unity-Magnitude Input Shapers and their Relation to Time-Optimal Control , 1996 .

[2]  Vicente Feliu,et al.  Adaptive input shaping for single-link flexible manipulators using an algebraic identification , 2012 .

[3]  William Singhose,et al.  A controller enabling precise positioning and sway reduction in bridge and gantry cranes , 2007 .

[4]  M. O. Tokhi,et al.  Control of a gantry crane using input-shaping schemes with distributed delay , 2017 .

[5]  Zaharuddin Mohamed,et al.  Modelling and Sway Control of a Double-Pendulum Overhead Crane System , 2017 .

[6]  Warren P. Seering,et al.  Preshaping Command Inputs to Reduce System Vibration , 1990 .

[7]  M. O. Tokhi,et al.  Command shaping techniques for vibration control of a flexible robot manipulator , 2004 .

[8]  Richard Bearee,et al.  New Damped-Jerk trajectory for vibration reduction , 2014 .

[9]  D. K. Sharma,et al.  Measurement and Analysis of Surge Distribution in Motor Stator Windings , 1989, IEEE Power Engineering Review.

[10]  Shoji Moriyasu,et al.  Surge Propagation of PWM-Inverter and Surge Voltage on the Motor , 1999 .

[11]  Miguel Ayala Botto,et al.  Vibration control of a very flexible manipulator system , 2005 .

[12]  Lisa J. Porter,et al.  Vibration Reduction Using Multi-Hump Extra-Insensitive Input Shapers , 1995 .

[13]  William Singhose,et al.  Command Generation for Flexible Systems by Input Shaping and Command Smoothing , 2010 .

[14]  Auwalu M. Abdullahi,et al.  Model reference command shaping for vibration control of multimode flexible systems with application to a double-pendulum overhead crane , 2019, Mechanical Systems and Signal Processing.

[15]  Zaharuddin Mohamed,et al.  A neural network-based input shaping for swing suppression of an overhead crane under payload hoisting and mass variations , 2018, Mechanical Systems and Signal Processing.

[16]  Auwalu M. Abdullahi,et al.  Control strategies for crane systems: A comprehensive review , 2017 .

[17]  Warren P. Seering,et al.  Shaping inputs to reduce vibration: a vector diagram approach , 1990, Proceedings., IEEE International Conference on Robotics and Automation.

[18]  Warren P. Seering,et al.  DESIGN AND IMPLEMENTATION OF TIME-OPTIMAL NEGATIVE INPUT SHAPERS , 1994 .

[19]  MARIUSZ PAULUK,et al.  TIME OPTIMAL CONTROL OF 3 D CRANE , 2001 .

[20]  Abdul Rashid Husain,et al.  Improved input shaping technique for a nonlinear system , 2014, 2014 IEEE International Conference on Control System, Computing and Engineering (ICCSCE 2014).

[21]  Ziyad N. Masoud,et al.  A Smooth Wave-Form Command Shaping Control , 2013 .

[22]  G. G. Stokes.  "J." , 1890, The New Yale Book of Quotations.

[23]  William Singhose,et al.  DERIVATION AND PROPERTIES OF CONVOLVED AND SIMULTANEOUS TWO-MODE INPUT SHAPERS , 1996 .

[24]  William Singhose,et al.  A comparison of input shaping and time-optimal flexible-body control , 1997 .