Piezo-activated guided wave propagation and interaction with damage in tubular structures

This study investigated propagation characteristics of piezo-activated guided waves in an aluminium rectangular-section tube for the purpose of damage identification. Changes in propagating velocity and amplitude of the first wave packet in acquired signals were observed in the frequency range from 50 to 250 kHz. The difference in guided wave propagation between rectangular- and circular-section tubes was examined using finite element simulation, demonstrating a great challenge in interpretation of guided wave signals in rectangular-section tubes. An active sensor network, consisting of nine PZT elements bonded on different surfaces of the tube, was configured to collect the wave signals scattered from through-thickness holes of different diameters. It was found that guided waves were capable of propagating across the sharp tube curvatures while retaining sensitivity to damage, even that not located on the surfaces where actuators/sensors were attached. Signal correlation between the intact and damaged structures was evaluated with the assistance of a concept of digital damage fingerprints (DDFs). The probability of the presence of damage on the unfolded tube surface was thus obtained, by which means the position of damage was identified with good accuracy.

[1]  Ser Tong Quek,et al.  Detection of cracks in cylindrical pipes and plates using piezo-actuated Lamb waves , 2005 .

[2]  Victor Giurgiutiu,et al.  Embedded non-destructive evaluation for structural health monitoring, damage detection, and failure prevention , 2005 .

[3]  M. Silk,et al.  The propagation in metal tubing of ultrasonic wave modes equivalent to Lamb waves , 1979 .

[4]  Moon Ho Park,et al.  Ultrasonic inspection of long steel pipes using Lamb waves , 1996 .

[5]  Suszanne Thwaites,et al.  NON-DESTRUCTIVE TESTING OF HONEYCOMB SANDWICH STRUCTURES USING ELASTIC WAVES , 1995 .

[6]  P. Cawley,et al.  Surface wave modes in rails , 2006 .

[7]  M. Lowe,et al.  Defect detection in pipes using guided waves , 1998 .

[8]  Peter Cawley,et al.  THE REFLECTION OF GUIDED WAVES FROM NOTCHES IN PIPES: A GUIDE FOR INTERPRETING CORROSION MEASUREMENTS , 2004 .

[9]  Ivan Bartoli,et al.  The response of rectangular piezoelectric sensors to Rayleigh and Lamb ultrasonic waves , 2007 .

[10]  Joseph L. Rose,et al.  Active health monitoring of an aircraft wing with embedded piezoelectric sensor/actuator network: I. Defect detection, localization and growth monitoring , 2007 .

[11]  L. Ye,et al.  Quantitative evaluation of crack orientation in aluminium plates based on Lamb waves , 2007 .

[12]  Joseph L. Rose,et al.  High frequency guided wave natural focusing pipe inspection with frequency and angle tuning , 2006 .

[13]  P. Cawley,et al.  The use of Lamb waves for the long range inspection of large structures , 1996 .

[14]  Butrus T. Khuri-Yakub,et al.  Lamb Wave Tomography and Its Application in Pipe Erosion/Corrosion Monitoring , 1996 .

[15]  Thomas Monnier,et al.  Lamb Waves-based Impact Damage Monitoring of a Stiffened Aircraft Panel using Piezoelectric Transducers , 2006 .

[16]  P. Cawley,et al.  The low-frequency reflection and scattering of the S0 Lamb mode from a circular through-thickness hole in a plate: Finite Element, analytical and experimental studies. , 2002, The Journal of the Acoustical Society of America.

[17]  J Qu,et al.  Crack characterization using guided circumferential waves. , 2001, The Journal of the Acoustical Society of America.

[18]  Lin Ye,et al.  Time-domain Analyses and Correlations of Lamb Wave Signals for Damage Detection in a Composite Panel of Multiple Stiffeners , 2009 .

[19]  Peter Cawley,et al.  The Potential of Guided Waves for Monitoring Large Areas of Metallic Aircraft Fuselage Structure , 2001 .

[20]  M. Hinders,et al.  Guided wave helical ultrasonic tomography of pipes. , 2003, The Journal of the Acoustical Society of America.

[21]  Joseph L. Rose,et al.  A comparison of embedded sensor Lamb wave ultrasonic tomography approaches for material loss detection , 2006 .

[22]  Fuh-Gwo Yuan,et al.  A pre-stack migration method for damage identification in composite structures , 2007 .

[23]  A. G. Roosenbrand,et al.  The reflection of the fundamental torsional mode from cracks and notches in pipes. , 2003, The Journal of the Acoustical Society of America.

[24]  Francesco Lanza di Scalea,et al.  Wavelet-based feature extraction for automatic defect classification in strands by ultrasonic structural monitoring , 2006 .

[25]  Sébastien Grondel,et al.  Fatigue crack monitoring of riveted aluminium strap joints by Lamb wave analysis and acoustic emission measurement techniques , 2002 .

[26]  Peter Cawley,et al.  Monitoring the setting and early hardening of concrete using an ultrasonic waveguide , 2004 .

[27]  L. Ye,et al.  Quantitative assessment of through-thickness crack size based on Lamb wave scattering in aluminium plates , 2008 .

[28]  Dong Wang,et al.  A Probabilistic Diagnostic Algorithm for Identification of Multiple Notches Using Digital Damage Fingerprints (DDFs) , 2009 .