Investigation on the chip formation concerning tool inclination angles in ball end milling of H13 die steel

Widespread application of ball end milling operation is an outstanding characteristic in the field of manufacturing of die and molds. Tool inclination angles, which could improve the cutting performance of ball end mill, are critical factor in the ball end milling process, and also chip formation is one of the most important phenomena in the machining process. Numerical simulation, geometric analysis, observation by optical microscope and scanning electron microscope, and energy-dispersive spectroscopy analysis were adopted to study the chip formation during ball end milling of H13 die steels involving tool inclination angles in this work. The theoretical uncut chip geometry and tool–work contact zone were analyzed by computer-aided modeling technology. Finite element modeling of chip formation process involving tool inclination angles was performed, and variations of the maximum chip temperature which could provide assistant understanding of practical chip formation were analyzed. This article also investigated the practical chip morphologies, chip color, and the cutting characteristics under different process conditions and tool inclination angles. The optical microscope and scanning electronic microscope were used to capture the micro-photos of the chips under different process parameters, and the chip color and chip morphologies were discussed together with the cutting characteristics with regard to various process parameters. Energy-dispersive spectroscopy analysis of the chip free surface and back surface was also carried out for some special tool inclination angles. Deep understanding of the chip formation in multi-axis milling process was enhanced, and the research work could provide support for the selection of process parameters to some extent.

[1]  Hsi-Yung Feng,et al.  The prediction of cutting forces in the ball-end milling process—I. Model formulation and model building procedure , 1994 .

[2]  Y. Liao,et al.  Prediction of cutting forces in ball-end milling by means of geometric analysis , 2008 .

[3]  Wei Zhaocheng,et al.  Cutting force prediction in ball end milling of sculptured surface with Z-level contouring tool path , 2011 .

[4]  J. Paulo Davim,et al.  State-of-the-art research in machinability of hardened steels , 2013 .

[5]  Paul Mativenga,et al.  An Investigation of Tool Chip Contact Phenomena in High-Speed Turning Using Coated Tools , 2006 .

[6]  Yuebin Guo,et al.  An experimental and analytical analysis on chip morphology, phase transformation, oxidation, and their relationships in finish hard milling , 2009 .

[7]  Xin-Guang Liang,et al.  An accuracy algorithm for chip thickness modeling in 5-axis ball-end finish milling , 2011, Comput. Aided Des..

[8]  Sang-Moon Hwang,et al.  Chip load prediction in ball-end milling , 2001 .

[9]  S. Spiewak,et al.  An Improved Model of the Chip Thickness in Milling , 1995 .

[10]  Guillaume Fromentin,et al.  Geometrical analysis of thread milling—part 2: calculation of uncut chip thickness , 2010 .

[11]  C. K. Toh,et al.  Comparison of chip surface temperature between up and down milling orientations in high speed rough milling of hardened steel , 2005 .

[12]  C. Y. Wang,et al.  Finite-Element Simulation of Conventional and High-Speed Peripheral Milling of Hardened Mold Steel , 2009 .

[13]  D. Aspinwall,et al.  3D FE modelling of high-speed ball nose end milling , 2010 .

[14]  Yadong Gong,et al.  Chip formation analysis in micromilling operation , 2009 .

[15]  Andrew Y. C. Nee,et al.  Theoretical modelling and simulation of cutting forces in face milling with cutter runout , 1999 .

[16]  Yoke San Wong,et al.  Investigation of chip formation in high speed end milling , 2001 .

[17]  M. C. Shaw,et al.  Chip Formation in the Machining of Hardened Steel , 1993 .

[18]  Min Wan,et al.  Calculations of chip thickness and cutting forces in flexible end milling , 2006 .

[19]  I. S. Jawahir,et al.  Some Observations of the Chip Formation Process and the White Layer Formation in High Speed Milling of Hardened Steel , 2004 .

[20]  Suhas S. Joshi,et al.  Analytical modeling of chip geometry and cutting forces in helical ball end milling of superalloy Inconel 718 , 2010 .

[21]  Konstantinos-Dionysios Bouzakis,et al.  Determination of the chip geometry, cutting force and roughness in free form surfaces finishing milling, with ball end tools , 2003 .

[22]  Steven Y. Liang,et al.  ANALYTICAL MODELING OF FORCE SYSTEM IN BALL-END MILLING , 1997 .

[23]  Min-Yang Yang,et al.  The prediction of cutting force in ball-end milling , 1991 .

[24]  A. Moufki,et al.  Modelling of cutting forces in ball-end milling with tool–surface inclination: Part I: Predictive force model and experimental validation , 2007 .

[25]  Jibin Zhao,et al.  Model of End Milling Force Based on Undeformed Chip Surface with NURBS in Peripheral Milling , 2010 .

[26]  Martin Loftus,et al.  Prediction of Surface Quality from Ball-Nose Milling in High-Speed Machining Applications , 2006 .

[27]  Michele Monno,et al.  3D finite element modeling of face milling of continuous chip material , 2010 .

[28]  Paul Mativenga,et al.  Estimation of minimum chip thickness in micro-milling using acoustic emission , 2011 .