Development of a microchannel evaporator model for a CO2 air-conditioning system

This paper presents the development and verification of a heat exchanger model for evaluating the thermal performance of an evaporator for a CO2 mobile air-conditioning system. The model has been developed, on the basis of the finite volume method, with emphasis placed on the air-side heat and mass transfer processes. The governing equations are derived from mass and energy balances using the newly developed air-side heat transfer and friction loss correlations for microchannel heat exchangers under both dry and wet conditions. The calculated air-side heat transfer and pressure drop data are in good agreement with measured data. However, the refrigerant-side pressure drop estimation for microchannel tubes usually underestimates the measured value. The simulation results and importance of selecting appropriate heat transfer and pressure drop correlations for the microchannel heat exchanger are addressed.

[1]  Armin Hafner,et al.  Development of compact heat exchangers for CO2 air-conditioning systems☆ , 1998 .

[2]  Clark W. Bullard,et al.  Air-side thermal hydraulic performance of multi-louvered fin aluminum heat exchangers , 2002 .

[3]  Chi-Chuan Wang,et al.  Air Side Performance of Brazed Aluminum Heat Exchangers , 1996 .

[4]  M. Shah.  Chart correlation for saturated boiling heat transfer: Equations and further study , 1982 .

[5]  Svend Tollak Munkejord,et al.  Heat Transfer and Pressure Drop for Flow of Supercritical and Subcritical CO2 in Microchannel Tubes , 2000 .

[6]  P. L. Dhar,et al.  A new procedure for performance prediction of air conditioning coils , 1998 .

[7]  K. Gungor,et al.  Simplified general correlation for saturated flow boiling and comparisons of correlations with data , 1987 .

[8]  J. W. Ramsey,et al.  Thermal Environmental Engineering , 1970 .

[9]  Chi-Chuan Wang,et al.  Performance of plate finned tube heat exchangers under dehumidifying conditions , 1997 .

[10]  S. Kandlikar.  A General Correlation for Saturated Two-Phase Flow Boiling Heat Transfer Inside Horizontal and Vertical Tubes , 1990 .

[11]  P. Hrnjak,et al.  Pressure Drop Measurements in Microchannel Heat Exchanger , 2000 .

[12]  A. H. Elmahdy,et al.  PERFORMANCE SIMULATION OF MULTI-ROW DRY (AND / OR WET) HEAT EXCHANGERS , 1978 .

[13]  M. W. Wambsganss,et al.  Two-phase pressure drop of refrigerants during flow boiling in small channels : an experimental investigation and correlation development. , 1999 .

[14]  R. Shah,et al.  An Assessment of Refrigerant Heat Transfer, Pressure Drop, and Void Fraction Effects In Microfin Tubes , 2001 .

[15]  A. C. Kirkwood.  Modeling, Design, and Testing of a Microchannel Split-System Air Conditioner , 1999 .

[16]  C. W. Bullard,et al.  Air-Side Thermal Performance of Micro-Channel Heat Exchangers Under Dehumidifying Conditions , 2000 .

[17]  Reinhard Radermacher,et al.  A heat exchanger model for mixtures and pure refrigerant cycle simulations , 1997 .

[18]  T. A. Cowell,et al.  Heat transfer and pressure drop characteristics of flat tube and louvered plate fin surfaces , 1988 .

[19]  B. S. Petukhov.  Heat Transfer and Friction in Turbulent Pipe Flow with Variable Physical Properties , 1970 .

[20]  Chi-Chuan Wang,et al.  A generalized heat transfer correlation for Iouver fin geometry , 1997 .

[21]  J. Wattelet.  EVAPORATIVE CHARACTERISTICS OF R-12, R-134a AND A MIXTURE AT LOW MASS FLUXES , 1994 .

[22]  L. Friedel.  Improved Friction Pressure Drop Correlation for Horizontal and Vertical Two-Phase Pipe Flow , 1979 .

[23]  Y. J. Chang,et al.  Heat transfer and flow characteristics of automotive brazed aluminum heat exchangers , 1994 .