Preferred Tool Shapes for Various Horizontal and Vertical Work Locations

Abstract Thirty-six subjects rated seven vertical and four horizontal positions after driving 25 screws at each of these work locations. The four horizontal work locations ranged from 13 to 88 cm and the seven vertical work locations ranged from 38 to 191 cm. Pneumatic tools (torque set to 3.2 Nm) with three varying shapes (pistol, in-line, and right-angle) were used to drive the screws into perforated sheet metal. Before rating each work combination with the Borg ten-point ratio rating scale, subjects were asked to imagine that they were an assembly line worker who was required to drive screws at that work location and with that particular tool for 8 hours. The work location/tool combination that received the lowest ratings of perceived exertion for the vertical surface were given after using the pistol tool to drive screws between 114 and 140 cm. Using the right-angle or the in-line tool to drive screws at distances between 13 and 38 cm received the lowest ratings of perceived exertion on the horizontal...

[1]  T J Armstrong,et al.  Investigation of cumulative trauma disorders in a poultry processing plant. , 1982, American Industrial Hygiene Association journal.

[2]  T. Teichmann,et al.  An introduction to mathematical statistics , 1960 .

[3]  E N Corlett,et al.  The ergonomics of spot welders. , 1978, Applied ergonomics.

[4]  W S Marras,et al.  Effects of Handle Angle and Work Orientation on Hammering: I. Wrist Motion and Hammering Performance , 1989, Human factors.

[5]  A Kilbom,et al.  Horizontal lifting--physiological and psychological responses. , 1982, Ergonomics.

[6]  S H Snook,et al.  Psychophysical considerations in permissible loads. , 1985, Ergonomics.

[7]  G D Herrin,et al.  Prediction of overexertion injuries using biomechanical and psychophysical models. , 1986, American Industrial Hygiene Association journal.

[8]  S H Snook,et al.  Maximum weights and work loads acceptable to male industrial workers. A study of lifting, lowering, pushing, pulling, carrying, and walking tasks. , 1970, American Industrial Hygiene Association journal.

[9]  M. M. Ayoub,et al.  A Job Severity Index for the Evaluation and Control of Lifting Injury , 1984, Human factors.

[10]  B. Noble,et al.  Clinical applications of perceived exertion. , 1982, Medicine and science in sports and exercise.

[11]  G. Borg.  Perceived exertion as an indicator of somatic stress. , 2019, Scandinavian journal of rehabilitation medicine.

[12]  S H Snook,et al.  The evaluation of physical tasks in industry. , 1966, American Industrial Hygiene Association journal.

[13]  G. B. Wetherill,et al.  Quality Control and Industrial Statistics , 1975 .

[14]  R. Larsen,et al.  An introduction to mathematical statistics and its applications (2nd edition) , by R. J. Larsen and M. L. Marx. Pp 630. £17·95. 1987. ISBN 13-487166-9 (Prentice-Hall) , 1987, The Mathematical Gazette.

[15]  M Hagberg,et al.  Discomfort and load on the upper trapezius muscle when operating a wordprocessor. , 1986, Ergonomics.

[16]  S H Snook,et al.  Perceived exertion and discomfort versus work height with a pistol-shaped screwdriver. , 1990, American Industrial Hygiene Association journal.

[17]  Stover H. Snook,et al.  The Ergonomics Society The Society's Lecture 1978. THE DESIGN OF MANUAL HANDLING TASKS , 1978 .

[18]  G. S. Phalen,et al.  The carpal-tunnel syndrome. Seventeen years' experience in diagnosis and treatment of six hundred fifty-four hands. , 1966, The Journal of bone and joint surgery. American volume.

[19]  S J Legg,et al.  Metabolic and cardiovascular cost, and perceived effort over an 8 hour day when lifting loads selected by the psychophysical method. , 1985, Ergonomics.

[20]  T J Armstrong,et al.  Ergonomics considerations in hand and wrist tendinitis. , 1987, The Journal of hand surgery.

[21]  I Petersén,et al.  Shoulder pain in industry: an epidemiological study on welders. , 1981, Acta orthopaedica Scandinavica.

[22]  Hoffman Gs.  Tendinitis and bursitis. , 1981 .

[23]  W M Keyserling.  Postural analysis of the trunk and shoulders in simulated real time. , 1986, Ergonomics.

[24]  M G Wardle,et al.  A Psychophysical Approach to Estimating Endurance in Performing Physically Demanding Work , 1978, Human factors.

[25]  M Hagberg,et al.  Work load and fatigue in repetitive arm elevations. , 1981, Ergonomics.

[26]  G. Sternbach,et al.  The carpal tunnel syndrome. , 1999, The Journal of emergency medicine.

[27]  D B Chaffin,et al.  Some biomechanical aspects of the carpal tunnel. , 1979, Journal of biomechanics.

[28]  T. Armstrong,et al.  Occupational factors and carpal tunnel syndrome. , 1987, American journal of industrial medicine.

[29]  S H Snook,et al.  Maximum frequency of lift acceptable to male industrial workers. , 1968, American Industrial Hygiene Association journal.

[30]  S. Snook,et al.  A study of three preventive approaches to low back injury. , 1978, Journal of occupational medicine. : official publication of the Industrial Medical Association.

[31]  Laura Punnett,et al.  Subjective Worker Assessments of Hand Tools Used in Automobile Assembly , 1989 .

[32]  T J Armstrong,et al.  Repetitive Trauma Disorders: Job Evaluation and Design , 1986, Human factors.

[33]  E N Corlett,et al.  A technique for assessing postural discomfort. , 1976, Ergonomics.

[34]  J D Troup,et al.  A psychophysical study of heaviness for box lifting and lowering. , 1986, Ergonomics.