Decreasing the surface roughness of aluminum alloy welds fabricated by a dual beam laser

[1]  R. Kovacevic,et al.  Effect of laser beam configuration on microstructure evolution and joint performance in laser joining AA 6111 panels , 2017 .

[2]  Radovan Kovacevic,et al.  Multiresponse Optimization of Laser Cladding Steel + VC Using Grey Relational Analysis in the Taguchi Method , 2016 .

[3]  H L Wei,et al.  Evolution of solidification texture during additive manufacturing , 2015, Scientific Reports.

[4]  Wei Liu,et al.  3D-imaging of selective laser melting defects in a Co–Cr–Mo alloy by synchrotron radiation micro-CT , 2015 .

[5]  William S. Janna,et al.  Introduction to Fluid Mechanics , 1973 .

[6]  P. Parvin,et al.  The influence of different volume ratios of He and Ar in shielding gas mixture on the power waste parameters for Nd:YAG and CO2 laser welding , 2013 .

[7]  P. Wei.  The Physics of Weld Bead Defects , 2012 .

[8]  Nie Zuoren,et al.  Optimization of weld bead geometry in laser welding with filler wire process using Taguchi’s approach , 2012 .

[9]  T. DebRoy,et al.  Mechanisms of Spiking and Humping in Keyhole Welding , 2012, IEEE Transactions on Components, Packaging and Manufacturing Technology.

[10]  L. Quintino,et al.  Gas shielding in fibre laser welding of high strength pipeline steel , 2011 .

[11]  T. DebRoy,et al.  Scaling of spiking and humping in keyhole welding , 2011 .

[12]  Ni Xian-sheng,et al.  The use of Taguchi method to optimize the laser welding of sealing neuro-stimulator , 2011 .

[13]  U. Reisgen,et al.  Shielding gas influences on laser weldability of tailored blanks of advanced automotive steels , 2010 .

[14]  A. Fortunato,et al.  Hybrid laser-MIG welding of aluminum alloys: The influence of shielding gases , 2009 .

[15]  T. Kuo,et al.  Effects of Different Shielding Gases and Power Waveforms on Penetration Characteristics and Porosity Formation in Laser Welding of Inconel 690 Alloy , 2007 .

[16]  S. Katayama,et al.  Physical Phenomena and Porosity Prevention Mechanism in Laser-Arc Hybrid Welding , 2006 .

[17]  T. Kuo,et al.  Effects of Shielding Gas Flow Rate and Power Waveform on Nd:YAG Laser Welding of A5754-O Aluminum Alloy , 2006 .

[18]  G. Deyev,et al.  Surface Phenomena in Fusion Welding Processes , 2005 .

[19]  C. Wang,et al.  Optimization of Nd:YAG laser welding onto magnesium alloy via Taguchi analysis , 2005 .

[20]  P. Durbin,et al.  Statistical Theory and Modeling for Turbulent Flows , 2001 .

[21]  M. Backhaus-Ricoult.  A model of oxygen-activity-dependent adsorption (desorption) to metal–oxide interfaces , 2000 .

[22]  Naoki Seto,et al.  High-speed simultaneous observation of plasma and keyhole behavior during high power CO2 laser welding: Effect of shielding gas on porosity formation , 2000 .

[23]  B. Chung,et al.  The effect of shielding gas types on CO2 laser tailored blank weldability of low carbon automotive galvanized steel , 1999 .

[24]  G. M. Grigorenko,et al.  Theoretical and Experimental Investigation of the Thermodynamic and Kinetic Nitrogen Absorption by Liquid Alloys , 1999 .

[25]  Lay Kee Ang,et al.  Surface instability of multipulse laser ablation on a metallic target , 1998 .

[26]  Pengsheng Wei,et al.  Surface Ripple in Electron-Beam Welding Solidification , 1996 .

[27]  Marc Sentis,et al.  2D modeling of laser-induced plume expansion near the plasma ignition threshold , 1996 .

[28]  M. Gharib,et al.  The role of streamwise vorticity in the near-field entrainment of round jets , 1992, Journal of Fluid Mechanics.

[29]  M. Seki,et al.  Possible mechanism of the roughness formation on a liquid layer caused by a high heat flux , 1992 .

[30]  R. Trivedi,et al.  MORPHOLOGICAL STABILITY OF A PLANAR INTERFACE UNDER RAPID SOLIDIFICATION CONDITIONS , 1986 .

[31]  Philippe M. Fauchet,et al.  Stimulated Wood's anomalies on laser-illuminated surfaces , 1986 .

[32]  Michael J. Aziz,et al.  Model for solute redistribution during rapid solidification , 1982 .

[33]  D. Kotecki,et al.  MECHANISM OF RIPPLE FORMATION DURING WELD SOLIDIFICATION , 1972 .

[34]  P. Sathiya,et al.  Effect of shielding gases on microstructure and mechanical properties of super austenitic stainless steel by hybrid welding , 2012 .

[35]  Rudolf Weber,et al.  Understanding of Humping Based on Conservation of Volume Flow , 2011 .

[36]  J. Brooks,et al.  CHAPTER 2 - Solidification and Structure of Welds , 1990 .

[37]  Yoshiaki Arata,et al.  Plasma Electron and Laser Beam Technology: Development and Use in Materials Processing , 1986 .

[38]  A. Adamson.  Physical chemistry of surfaces , 1960 .