A microfabricated suspended-tube chemical reactor for thermally efficient fuel processing

We present a suspended-tube chemical reactor/heat exchanger for high-temperature fuel processing in micro energy conversion systems, primarily for hydrogen production in portable fuel cell systems. This reactor, designed to thermally isolate a high-temperature reaction zone, consists of four free-standing silicon nitride tubes comprising two independent U-shaped fluidic channels. Portions of the tubes are encased in silicon to enable heat exchange between the fluids in these channels. A thin-film platinum resistor is embedded for localized heating and temperature sensing. This paper describes the design and fabrication process for the MEMS fuel processor. Fluidic testing, thermal characterization up to 825/spl deg/C, and preparation of catalyst washcoats in the reactor microchannels are discussed. In addition, results from catalytic autothermal butane combustion and ammonia cracking in the reactor are presented.

[1]  G. A. Slack,et al.  Thermal Conductivity of Silicon and Germanium from 3°K to the Melting Point , 1964 .

[2]  C. Geankoplis.  Transport processes and unit operations , 1978 .

[3]  D. L. Brownell,et al.  Handbook of Applied Thermal Design , 1988 .

[4]  V. Peletskii.  The investigation of thermal conductivity of silicon nitride , 1993 .

[5]  K. Pister,et al.  3D structures with piezoresistive sensors in standard CMOS , 1995, Proceedings IEEE Micro Electro Mechanical Systems. 1995.

[6]  Kristin L. Wood,et al.  Feasibility of micro power supplies for MEMS , 1997 .

[7]  Henry H. Voss,et al.  Portable fuel cell power generator , 1997 .

[8]  D. Chadwick,et al.  Effect of pH of Precipitation on the Preparation of High Surface Area Aluminas from Nitrate Solutions , 1998 .

[9]  M. Burns,et al.  Microfabricated capillarity-driven stop valve and sample injector , 1998, Proceedings MEMS 98. IEEE. Eleventh Annual International Workshop on Micro Electro Mechanical Systems. An Investigation of Micro Structures, Sensors, Actuators, Machines and Systems (Cat. No.98CH36176.

[10]  W. Hoffman,et al.  The far-reaching nature of microtube technology , 1998 .

[11]  K. Jensen,et al.  Investigation of high-temperature degradation of platinum thin films with an in situ resistance measurement apparatus , 1998 .

[12]  Xin Zhang,et al.  A six-wafer combustion system for a silicon micro gas turbine engine , 2000, Journal of Microelectromechanical Systems.

[13]  Klavs F. Jensen,et al.  Microfabricated multiphase packed-bed reactors : Characterization of mass transfer and reactions , 2001 .

[14]  K. Jensen,et al.  A Combustion-Based MEMS Thermoelectric Power Generator , 2001 .

[15]  W. Thomson,et al.  Catalytic Micro-Reactor Systems for Hydrogen Generation , 2001 .

[16]  Khalil Najafi,et al.  An Integrated Combustor-Thermoelectric Micro Power Generator , 2001 .

[17]  Mayuresh V. Kothare,et al.  A microreactor for in-situ hydrogen production by catalytic methanol reforming , 2001 .

[18]  S. Ha,et al.  Direct formic acid fuel cells , 2002 .

[19]  Suk Won Cha,et al.  Design and fabrication of a micro fuel cell array with “flip-flop” interconnection , 2002 .

[20]  Jaesung Han,et al.  Direct methanol fuel-cell combined with a small back-up battery , 2002 .

[21]  Yong Wang,et al.  Development of a soldier-portable fuel cell power system. Part I: A bread-board methanol fuel processor , 2002 .

[22]  Evan O. Jones,et al.  Microfuel processor for use in a miniature power supply , 2002 .

[23]  J. Meyers,et al.  Miniature fuel cells for portable power: Design considerations and challenges , 2002 .

[24]  Christopher Hebling,et al.  Fuel Cells for Low Power Applications , 2002 .