Improving sensitivity of an inductive pulse sensor for detection of metallic wear debris in lubricants using parallel LC resonance method

Detection of small metallic wear debris is critical to identify abnormal wear conditions for prognosis of pending machinery failure. In this paper we applied an inductance–capacitance (LC) resonance method to an inductive pulse debris sensor to increase the sensitivity. By adding an external capacitor to the sensing coil of the sensor, a parallel LC resonance circuit is formed that has a unique resonant frequency. At an excitation frequency close to the resonant frequency, impedance change (and thus change in voltage output) of the LC circuit caused by the passage of a debris particle is amplified due to sharp change in impedance at the resonant peak; thus signal-to-noise ratio and sensitivity are significantly improved. Using an optimized measurement circuit, iron particles ranging from 32 to 96 µm and copper particles ranging from 75 to 172 µm were tested. Results showed that the parallel LC resonance method is capable of detecting a 20 µm iron particle and a 55 µm copper particle while detection limits for the non-resonance method are 45 and 125 µm, respectively. In contrast to the non-resonant method, the sensitivity of the resonance method has been significantly improved.

[1]  Jiang Zhe,et al.  Parallel Sensing of Metallic Wear Debris in Lubricants Using Undersampling Data Processing , 2012 .

[2]  L. Dziczkowski.  Effect of eddy current frequency on measuring properties of devices used in non- destructive measurements of non-ferromagnetic metal plates , 2008 .

[3]  Anand Prabhakaran,et al.  Condition monitoring of steam turbine-generator through contamination analysis of used lubricating oil , 1999 .

[4]  Gary E. Newell.  Oil analysis cost‐effective machine condition monitoring technique , 1999 .

[5]  Michael N Kotzalas,et al.  Tribological advancements for reliable wind turbine performance , 2010, Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences.

[6]  Giorgio Dalpiaz,et al.  CONDITION MONITORING AND DIAGNOSTICS IN AUTOMATIC MACHINES: COMPARISON OF VIBRATION ANALYSIS TECHNIQUES , 1997 .

[7]  Habib Mohamadian,et al.  Various shape memory effects of stimuli-responsive shape memory polymers , 2013 .

[8]  J. R. Jordan,et al.  An inductive method for estimating the composition and size of metal particles , 1990 .

[9]  Joan Carletta,et al.  A microfluidic multichannel resistive pulse sensor using frequency division multiplexing for high throughput counting of micro particles , 2011 .

[10]  Saurabh Kumar,et al.  Online condition monitoring of engine oil , 2005 .

[11]  Li Du,et al.  A high throughput inductive pulse sensor for online oil debris monitoring , 2011 .

[12]  J. Mathew,et al.  The condition monitoring of rolling element bearings using vibration analysis , 1984 .

[13]  Joan Carletta,et al.  Inductive Coulter counting: detection and differentiation of metal wear particles in lubricant , 2010 .

[14]  Li Du,et al.  On-line Wear Debris Detection in Lubricating Oil for Condition Based Health Monitoring of Rotary Machinery , 2011 .

[15]  Julian Blanchard,et al.  History of electrical resonance , 1941, Electrical Engineering.

[16]  Carl Byington,et al.  Combined lubrication monitor for on-line gearbox health assessment , 2011, 2011 Aerospace Conference.

[17]  Wolfgang Cartellieri,et al.  Particulate analysis of light duty diesel engines (IDI&DI) with particular reference to the lube oil particulate fraction , 1984 .

[18]  H. W. Whittington,et al.  Improved transducer design for machine wear debris monitoring , 1995 .

[19]  Anand Asundi.  Digital Holography for MEMS and Microsystem Metrology: Asundi/Digital Holography for MEMS and Microsystem Metrology , 2011 .

[20]  Andrew P. Longstaff,et al.  Thermal analysis for condition monitoring of machine tool spindles , 2012 .

[21]  C. K. Toh,et al.  Vibration analysis in high speed rough and finish milling hardened steel , 2004 .

[22]  Andrew Hess,et al.  A helicopter powertrain diagnostics and prognostics demonstration , 2000, 2000 IEEE Aerospace Conference. Proceedings (Cat. No.00TH8484).