Developments of high strength Bi-containing Sn0.7Cu lead-free solder alloys prepared by directional solidification

Abstract Bi-containing Sn0.7Cu (SC) eutectic solder alloys were prepared and subjected to directional solidification, through which new types of fiber reinforced eutectic composites were generated. The influences of Bi addition on the microstructures and tensile properties of directionally solidified (DS) Bi-containing eutectic SC lead-free solder alloys have been investigated by using differential scanning calorimetry (DSC), scanning electron microscopy (SEM), energy dispersive spectrometry (EDS) and a tensile testing machine. The experimental results showed that addition of Bi could effectively reduce both the melting temperature and undercooling of SC solder alloy. The microstructures of DS SC– x Bi solder alloys were composed of Sn-rich phase (β) and Cu 6 Sn 5 fiber. No other intermetallic compounds (IMCs) with Bi content were observed in the solder matrix for SC solder alloys with various Bi contents. Both fiber spacing and diameter all decreased gradually with increasing growth rate and/or Bi content. Besides, the regularity of Cu 6 Sn 5 fibers alignment also decreased with increasing growth rate, too. The tensile strengths of the SC– x Bi eutectic solder alloys varied parabolically with growth rate ( R ). When R was 60 μm/s, maximum tensile strengths of 43.8, 55.2 and 56.37 MPa were reached for SC, SC0.7Bi and SC1.3Bi solder alloys. A comparison of tensile strength of SC, SC0.7Bi and SC1.3Bi with the same R indicated that the tensile strength increased with increasing Bi content, which was attributed to the presence of Bi and its role in refining microstructure and solid solution strengthening.

[1]  A. E. Hammad,et al.  Structural and elastic properties of eutectic Sn-Cu lead-free solder alloy containing small amount of Ag and in , 2011 .

[2]  T. Pollock,et al.  Development of Dendritic Structure in the Liquid-Metal-Cooled, Directional-Solidification Process , 2011 .

[3]  A. E. Hammad,et al.  Design of lead-free candidate alloys for low-temperature soldering applications based on the hypoeutectic Sn–6.5Zn alloy , 2014 .

[4]  G. Gottstein.  Physical Foundations of Materials Science , 2004 .

[5]  Ursula R. Kattner,et al.  On the Sn-Bi-Ag ternary phase diagram , 1994 .

[6]  M. Hon,et al.  Effects of aging time on the mechanical properties of Sn–9Zn–1.5Ag–xBi lead-free solder alloys , 2014 .

[7]  Yulong Li,et al.  Interfacial reaction and IMC growth between Bi-containing Sn0.7Cu solders and Cu substrate during soldering and aging , 2014 .

[8]  D. Witkin.  Influence of microstructure on quasi-static and dynamic mechanical properties of bismuth-containing lead-free solder alloys , 2012 .

[9]  K. Prabhu,et al.  Effect of temperature and substrate surface texture on wettability and morphology of IMCs between Sn–0.7Cu solder alloy and copper substrate , 2012, Journal of Materials Science: Materials in Electronics.

[10]  Sung K. Kang,et al.  Effects of Ti addition to Sn–Ag and Sn–Cu solders , 2012 .

[11]  S. Xue,et al.  Interfacial microstructure and properties of Sn–0.7Cu–0.05Ni/Cu solder joint with rare earth Nd addition , 2011 .

[12]  M. Palcut,et al.  Kinetics of intermetallic phase formation at the interface of Sn–Ag–Cu–X (X = Bi, In) solders with Cu substrate , 2011 .

[13]  L. Tsao,et al.  Effect of TiO2 nanoparticles on the microstructure and bonding strengths of Sn0.7Cu composite solder BGA packages with immersion Sn surface finish , 2012, Journal of Materials Science: Materials in Electronics.

[14]  Jun-Mo Yang,et al.  Aging treatment characteristics of solder bump joint for high reliability optical module , 2004 .

[15]  J. Hunt,et al.  Lamellar and Rod Eutectic Growth , 1988 .

[16]  A. E. Hammad,et al.  Microstructure, mechanical properties, and deformation behavior of Sn–1.0Ag–0.5Cu solder after Ni and Sb additions , 2013 .

[17]  Liang Zhang,et al.  Properties enhancement of SnAgCu solders containing rare earth Yb , 2014 .

[18]  Li Yang,et al.  Effects of Ag particles content on properties of Sn0.7Cu solder , 2013, Journal of Materials Science: Materials in Electronics.

[19]  L. Broutman,et al.  Modern Composite Materials , 1967 .

[20]  A. El-Daly,et al.  Enhanced ductility and mechanical strength of Ni-doped Sn–3.0Ag–0.5Cu lead-free solders , 2014 .

[21]  R. Mahmudi,et al.  Microstructure and tensile behavior of Sn–5Sb lead-free solder alloy containing Bi and Cu , 2011 .

[22]  J. Neuenschwander,et al.  Evolution of the microstructure of Sn–Ag–Cu solder joints exposed to ultrasonic waves during solidification , 2011 .

[23]  A. E. Hammad,et al.  Development of high strength Sn–0.7Cu solders with the addition of small amount of Ag and In , 2011 .

[24]  John Wulff,et al.  Introduction To Materials Science And Engineering , 1976 .

[25]  Ke Li,et al.  Microstructure evolution and mechanical properties of Sn0.7Cu0.7Bi lead-free solders produced by directional solidification , 2013 .

[26]  Xiaowu Hu,et al.  Rod-like structure and microhardness during directional solidification of Sn-1wt.%Cu eutectic alloy , 2012 .