Tool wear and machining performance of cBN–TiN coated carbide inserts and PCBN compact inserts in turning AISI 4340 hardened steel

Abstract PCBN is the dominant tool material for hard turning applications due to its high hardness, high wear resistance, and high thermal stability. However, the inflexibility of fabricating PCBN inserts with complex tool geometries and the prohibitive cost of PCBN inserts are some of the concerns in furthering the implementation of CBN based materials for hard turning. In this paper, we present the results of a thorough investigation of cBN plus TiN (cBN–TiN) composite-coated, commercial grade, carbide inserts (CNMA 432, WC–Co (6% Co)) for hard turning applications in an effort to address these concerns. The effect of cutting speed and feed rate on tool wear (tool life), surface roughness, and cutting forces of the cBN–TiN coated carbide inserts was experimented and analyzed using analysis of variance (ANOVA) technique, and the cutting conditions for their maximum tool life were evaluated. The tool wear, surface roughness, and cutting forces of the cBN–TiN coated and commercially available PCBN tipped inserts were compared under similar cutting conditions. Both flank wear and crater wear were observed. The flank wear is mainly due to abrasive actions of the martensite present in the hardened AISI 4340 alloy. The crater wear of the cBN–TiN coated inserts is less than that of the PCBN inserts because of the lubricity of TiN capping layer on the cBN–TiN coating. The coated CNMA 432 inserts produce a good surface finish (

[1]  M. M. Barash,et al.  Cutting mechanism during machining of hardened steel , 1987 .

[2]  Chun Liu,et al.  Single-step superfinish hard machining: Feasibility and feasible cutting conditions , 1996 .

[3]  C. R. Liu,et al.  A NEW CONCEPT FOR DECOUPLING THE CUTTING FORCES DUE TO TOOL FLANK WEAR AND CHIP FORMATION IN HARD TURNING , 1998 .

[4]  David K. Aspinwall,et al.  The Effect of Workpiece Hardness and Cutting Speed on the Machinability of AISI H13 Hot Work Die Steel When Using PCBN Tooling , 1999, Manufacturing Science and Engineering.

[5]  Moshe M. Barash,et al.  Experimental investigation on cubic boron nitride turning of hardened AISI 52100 steel , 2003 .

[6]  Fu Gang Yan,et al.  Cutting temperature and tool wear of hard turning hardened bearing steel , 2002 .

[7]  Hans Kurt Tönshoff,et al.  Tribological aspects of hard turning with ceramic tools , 1995 .

[8]  Hossam A. Kishawy,et al.  AN EXPERIMENTAL EVALUATION OF CUTTING TEMPERATURES DURING HIGH SPEED MACHINING OF HARDENED D2 TOOL STEEL , 2002 .

[9]  Mats Andersson,et al.  Effect of chamfer angle on wear of PCBN cutting tool , 2003 .

[10]  M. C. Shaw.  Metal Cutting Principles , 1960 .

[11]  M. Jacobson,et al.  Surface integrity of hard-turned M50 steel , 2002 .

[12]  Ajay P. Malshe,et al.  Cubic Boron Nitride (cBN) based nanocomposite coatings on cutting inserts with chip breakers for hard turning applications , 2005 .

[13]  R. Lappalainen,et al.  Comparison of cutting performance of ion-plated NbN, ZrN, TiN and (Ti, Al)N coatings , 1987 .

[14]  A. E. Diniz,et al.  Correlating tool wear, tool life, surface roughness and tool vibration in finish turning with coated carbide tools , 1994 .

[15]  Y. Kevin Chou,et al.  Tool wear mechanism in continuous cutting of hardened tool steels , 1997 .

[16]  János Kundrák,et al.  On the Dry Machining of Steel Surfaces Using Superhard Tools , 2002 .

[17]  Gerry Byrne,et al.  Cutting tool wear in the machining of hardened steels , 2001 .

[18]  M. Barash,et al.  Effect of Hardness on the Surface Integrity of AISI 4340 Steel , 1986 .

[19]  D. Bhat,et al.  Review of CVD TiN coatings for wear-resistant applications: deposition processes, properties and performance* , 1994 .

[20]  A. Moisan,et al.  Surface integrity in finish hard turning of case-hardened steels , 2003 .

[21]  A. Malshe,et al.  CBN-TiN Composite Coating Using a Novel Combinatorial Method—Structure and Performance in Metal Cutting , 2003 .