Selective Metallization Induced by Laser Activation: Fabricating Metallized Patterns on Polymer via Metal Oxide Composite.

Recently, metallization on polymer substrates has been given more attention due to its outstanding properties of both plastics and metals. In this study, the metal oxide composite of copper-chromium oxide (CuO·Cr2O3) was incorporated into the polymer matrix to design a good laser direct structuring (LDS) material, and the well-defined copper pattern (thickness =10 μm) was successfully fabricated through selective metallization based on 1064 nm near-infrared pulsed laser activation and electroless copper plating. We also prepared polymer composites incorporated with CuO and Cr2O3; however, these two polymer composites both had very poor capacity of selective metallization, which has no practical value for LDS technology. In our work, the key reasons causing the above results were systematically studied and elucidated using XPS, UV-vis-IR, optical microscopy, SEM, contact angle, ATR FTIR, and so on. The results showed that 54.0% Cu2+ in the polymer composite of CuO·Cr2O3 (the amount =5 wt %) is reduced to Cu0 (elemental copper) after laser activation (irradiation); however, this value is only 26.8% for the polymer composite of CuO (the amount =5 wt %). It was confirmed that to achieve a successful selective metallization after laser activation, not only was the new formed Cu0 (the catalytic seeds) the crucial factor, but the number of generated Cu0 catalytic seeds was also important. These two factors codetermined the final results of the selective metallization. The CuO·Cr2O3 is very suitable for applications of fabricating metallic patterns (e.g., metal decoration, circuit) on the inherent pure black or bright black polymer materials via LDS technology, which has a prospect of large-scale industrial applications.

[1]  Po-Da Hong,et al.  A simple method for acrylonitrile butadiene styrene metallization , 2013 .

[2]  L. Teixeira,et al.  Surface conditioning of ABS for metallization without the use of chromium baths , 2005 .

[3]  P. Rytlewski.  Laser-assisted metallization of composite coatings containing copper(II) acetylacetonate and copper(II) oxide or copper(II) hydroxide , 2014 .

[4]  Z. Li,et al.  Controlled synthesis of pure and highly dispersive Cu(II), Cu(I), and Cu(0)/MCM-41 with Cu[OCHMeCH2NMe2]2/MCM-41 as precursor , 2009 .

[5]  S. Babu,et al.  Excimer laser etching of polymers , 1986 .

[6]  T. Bessho,et al.  Layer by layer electroless deposition: An efficient route for preparing adhesion-enhanced metallic coatings on plastic surfaces , 2016 .

[7]  M. Cotte,et al.  Synchrotron-based FTIR microspectroscopy for the mapping of photo-oxidation and additives in acrylonitrile-butadiene-styrene model samples and historical objects. , 2014, Analytica chimica acta.

[8]  F. Başarir,et al.  Fabrication of gold patterns via multilayer transfer printing and electroless plating. , 2012, ACS applied materials & interfaces.

[9]  S. Palacin,et al.  Microscopic study of a ligand induced electroless plating process onto polymers. , 2010, ACS Applied Materials and Interfaces.

[10]  Yang Zhang,et al.  An electroless-plating-like solution deposition approach for large-area flexible thin films of transition metal oxide nanocrystals , 2014 .

[11]  Xuejiao Tang,et al.  Research on a new surface activation process for electroless plating on ABS plastic , 2008 .

[12]  J. Zhao,et al.  A Simple Way to Achieve Legible and Local Controllable Patterning for Polymers Based on a Near-Infrared Pulsed Laser. , 2016, ACS applied materials & interfaces.

[13]  Weihua Hu,et al.  Patterning of Metal Films on Arbitrary Substrates by Using Polydopamine as a UV-Sensitive Catalytic Layer for Electroless Deposition. , 2016, Langmuir : the ACS journal of surfaces and colloids.

[14]  J. Wang,et al.  Study of electroless copper plating on ABS resin surface modified by heterocyclic organosilane self-assembled film , 2014, Bulletin of Materials Science.

[15]  B. Shen,et al.  A novel surface activation method for Ni/Au electroless plating of acrylonitrile–butadiene–styrene , 2011 .

[16]  W. Dressick,et al.  Selective electroless metallization of patterned polymeric films for lithography applications. , 2009, ACS applied materials & interfaces.

[17]  I. Lee,et al.  A facile method of nickel electroless deposition on various neutral hydrophobic polymer surfaces , 2013 .

[18]  Jayesh G. Bokria,et al.  Spatial effects in the photodegradation of poly(acrylonitrile–butadiene–styrene): a study by ATR-FTIR , 2002 .

[19]  Jihai Zhang,et al.  Fabricating Metallic Circuit Patterns on Polymer Substrates through Laser and Selective Metallization. , 2016, ACS applied materials & interfaces.

[20]  S. Du,et al.  Electroless plating of PVC plastic through new surface modification method applying a semi-IPN hydrogel film , 2013 .

[21]  Y. Duh,et al.  Study on Exothermic Oxidation of Acrylonitrile-butadiene-styrene (ABS) Resin Powder with Application to ABS Processing Safety , 2010 .

[22]  Yucheng Wu,et al.  Electroless copper plating on PC engineering plastic with a novel palladium-free surface activation process , 2014 .

[23]  B. Shanks,et al.  Active species of copper chromite catalyst in C–O hydrogenolysis of 5-methylfurfuryl alcohol , 2012 .

[24]  J. Guilment,et al.  Determination of polybutadiene microstructures and styrene–butadiene copolymers composition by vibrational techniques combined with chemometric treatment , 2001 .

[25]  S. Tasaka,et al.  Thermal degradation of acrylonitrile–butadiene–styrene terpolymer in bean oil , 2001 .

[26]  De’an Yang,et al.  Autocatalytic deposition of copper coating on poly (ether ether ketone)/multiwalled carbon nanotubes composites via a palladium-free and simplified electroless process , 2015 .

[27]  P. Liu,et al.  Highly efficient and robust Au/MgCuCr2O4 catalyst for gas-phase oxidation of ethanol to acetaldehyde. , 2013, Journal of the American Chemical Society.

[28]  Lifang Liang,et al.  Site-selective metallization of polymeric substrates by the hyperbranched polymer templates , 2013 .

[29]  J. Fierro,et al.  Nature of Copper Active Sites in the Carbon Monoxide Oxidation on CuAl2O4and CuCr2O4Spinel Type Catalysts , 1998 .

[30]  Xuejiao Tang,et al.  A new palladium-free surface activation process for Ni electroless plating on ABS plastic , 2009 .

[31]  J. White,et al.  Copper oxide reduction through vacuum annealing , 2003 .

[32]  Chenxuan Wang,et al.  Growth and characterization of electro-deposited Cu2O and Cu thin films by amperometric I –T method on ITO/glass substrate , 2007 .

[33]  De’an Yang,et al.  Study on the pretreatment of poly(ether ether ketone)/multiwalled carbon nanotubes composites through environmentally friendly chemical etching and electrical properties of the chemically metallized composites. , 2013, ACS applied materials & interfaces.

[34]  T. Osaka,et al.  30years of electroless plating for semiconductor and polymer micro-systems , 2015 .

[35]  Minwei Wang,et al.  Optimization and kinetics of electroless Ni–P–B plating of quartz optical fiber , 2009 .