Preliminary thermodynamic study of regenerative Otto based cycles with zero NOx emissions operating with adiabatic and polytropic expansion

Abstract The aim of the paper is to demonstrate that a regenerative Otto cycle with adiabatic or polytropic expansion can achieve improved performance over traditional Otto engines, even exceeding the Carnot factor. Thus, the work deals with a novel regenerative Otto based internal combustion engine which differs from the conventional Otto thermal cycles in that the process of heat conversion into mechanical work is performed obeying a polytropic path function instead of the conventional adiabatic expansion without regeneration. Design characteristics concern the fact that combustion at constant volume is carried out undergoing large air excess so that the top combustion temperature is significantly lower than in conventional Otto cycles and consequently NOx emissions are neglected. Furthermore, during the polytropic expansion based path function, heat is absorbed by being submitted to a controlled heat flow rate, to achieve the desired polytropic expansion. The analysis of the regenerative Otto based on polytropic expansion is presented and results are compared with a regenerative Otto based on the adiabatic expansion and CF. The results show that a relevant advantage of the proposed regenerative Otto with polytropic expansion over the regenerative Otto cycle with adiabatic expansion involves performance enhancement within a wide range of combustion pressures, temperatures and regeneration capacities. Thus, thermal efficiency and specific work as function of the top combustion pressure ranges are of 71.95–58.43% and 143.5–173.6 kJ/kg respectively, when combustion pressures vary between 105 kPa and 200 kPa and CF is 60.8% (lower than the thermal efficiency). The successful results involving a compact engine structure, technically and economically viable, promises a new generation of efficient reciprocating internal combustion engines operating at relatively low temperatures.

[1]  M. Babaelahi,et al.  A new thermal model based on polytropic numerical simulation of Stirling engines , 2015 .

[2]  Anthony Paul Roskilly,et al.  Application of the Miller cycle to reduce NOx emissions from petrol engines , 2008 .

[3]  Tie Li,et al.  Fuel conversion efficiency improvements in a highly boosted spark-ignition engine with ultra-expansion cycle , 2015 .

[4]  Jim McGovern,et al.  Energy system feasibility study of an Otto cycle/Stirling cycle hybrid automotive engine , 2010 .

[5]  Yingru Zhao,et al.  Performance analysis of an irreversible Miller heat engine and its optimum criteria , 2007 .

[6]  Chih Wu,et al.  Performance analysis and optimization of a supercharged Miller cycle Otto engine , 2003 .

[7]  Hao Wang,et al.  Performance analysis and parametric optimum criteria of a quantum Otto heat engine with heat transfer effects , 2009 .

[8]  Pedro J. Mago,et al.  Modeling of reciprocating internal combustion engines for power generation and heat recovery , 2013 .

[9]  Srithar Rajoo,et al.  Waste heat recovery using a novel high performance low pressure turbine for electric turbocompounding in downsized gasoline engines: Experimental and computational analysis , 2015 .

[10]  Rahman Saidur,et al.  Technologies to recover exhaust heat from internal combustion engines , 2012 .

[11]  M. Babaelahi,et al.  A new closed-form analytical thermal model for simulating Stirling engines based on polytropic-finite speed thermodynamics , 2015 .

[12]  Alan Keromnes,et al.  Development and validation of a 5 stroke engine for range extenders application , 2014 .

[13]  Hans-Erik Ångström,et al.  A review of turbocompounding as a waste heat recovery system for internal combustion engines , 2015 .

[14]  Xiaosong Zhang,et al.  Thermodynamic analysis of a novel energy-efficient refrigeration system subcooled by liquid desiccant dehumidification and evaporation , 2014 .

[15]  Fengrui Sun,et al.  Finite-time thermodynamic modelling and analysis of an irreversible Otto-cycle , 2008 .

[16]  Shuhn-Shyurng Hou,et al.  Comparison of performances of air standard Atkinson and Otto cycles with heat transfer considerations , 2007 .

[17]  M. McLinden,et al.  NIST Standard Reference Database 23: Reference Fluid Thermodynamic and Transport Properties-REFPROP, Version 8.0 , 2007 .

[18]  Abdellah Shafieian,et al.  An investigation of heat recovery of submarine diesel engines for combined cooling, heating and power systems , 2016 .

[19]  Kangyao Deng,et al.  Thermodynamic analysis of an in-cylinder waste heat recovery system for internal combustion engines , 2014 .

[20]  Vahid Esfahanian,et al.  Energetic and exergetic analyses of a variable compression ratio spark ignition gas engine , 2014 .

[21]  Zhijun Wu,et al.  A high efficiency oxyfuel internal combustion engine cycle with water direct injection for waste heat recovery , 2014 .

[22]  Mokhtar Bidi,et al.  Optimization of powered Stirling heat engine with finite speed thermodynamics , 2016 .

[23]  Lingen Chen,et al.  Reciprocating heat-engine cycles , 2005 .

[24]  Anthony Paul Roskilly,et al.  An analytic study of applying Miller cycle to reduce NOx emission from petrol engine , 2007 .

[25]  Ricardo Novella,et al.  Potential of Atkinson cycle combined with EGR for pollutant control in a HD diesel engine , 2009 .

[26]  Anthony Paul Roskilly,et al.  A comparison of Miller and Otto cycle natural gas engines for small scale CHP applications , 2009 .

[27]  Ramón Ferreiro García,et al.  Isothermal and Adiabatic Expansion Based Trilateral Cycles , 2015 .

[28]  James P. Szybist,et al.  A Highly Efficient Six-Stroke Internal Combustion Engine Cycle with Water Injection for In-Cylinder Exhaust Heat Recovery , 2010 .

[29]  Antti Uusitalo,et al.  Technology competition in the internal combustion engine waste heat recovery: a patent landscape analysis , 2016 .

[30]  Lingen Chen,et al.  Thermodynamic simulation of performance of an Otto cycle with heat transfer and variable specific heats of working fluid , 2005 .

[31]  Fengrui Sun,et al.  Engine performance improved by controlling piston motion: Linear phenomenological law system Diesel cycle , 2012 .

[32]  Sridhar Thyageswaran,et al.  Regeneration in an internal combustion engine: Thermal-hydraulic modeling and analysis , 2016 .

[33]  Yingru Zhao,et al.  Optimization criteria for the important parameters of an irreversible Otto heat-engine , 2006 .

[34]  S. G. Penoncello,et al.  Thermodynamic Properties of Air and Mixtures of Nitrogen, Argon, and Oxygen From 60 to 2000 K at Pressures to 2000 MPa , 2000 .

[35]  Jincan Chen,et al.  An irreversible heat engine model including three typical thermodynamic cycles and their optimum performance analysis , 2007 .

[36]  Hoseyn Sayyaadi,et al.  Modified PSVL: A second order model for thermal simulation of Stirling engines based on convective–polytropic heat transfer of working spaces , 2015 .

[37]  Lingen Chen,et al.  Power, efficiency, entropy-generation rate and ecological optimization for a class of generalized irreversible universal heat-engine cycles , 2007 .