Edge-released, piezoelectric MEMS acoustic transducers in array configuration

A sensitive, broad-bandwidth piezoelectric microelectromechanical systems (MEMS) transducer based on frequency interleaving of resonant transducers was designed and fabricated. A sputter-deposited piezoelectric zinc oxide (ZnO) thin film on the diaphragm is used to sense and generate acoustic pressure. A high compliance cantilever and spiral-beam-supported diaphragms are designed and built on the edge-released MEMS structure to release initial residual stress and to avoid in-plane tension when bent. Stress compensation has been achieved by adjusting the thickness of each layer of the cantilever and by compensating for the ZnO film's compressive stress with the bimorph structure of the spiral-beam. For a given pressure level and diaphragm size, the maximum strain on the spiral-beam-supported diaphragm is about an order of magnitude larger than that of a rectangular cantilever diaphragm. Also, the acoustic transducer built on the spiral-beam-supported diaphragm has a much higher sensitivity (but with less tolerance on the fabrication process variation and at the cost of lower usable bandwidth) than the one built on a rectangular cantilever diaphragm. By connecting many transducers in parallel, both the sensitivity and acoustic output were improved about 30 times. The interleaving of the transducers increased not only the sensitivity, but also broadened the useable bandwidth.

[1]  Hideo Yoshihara,et al.  Silicon Nitride Single-Layer X-Ray Mask , 1981 .

[2]  Patricia M. Nieva,et al.  Design and characterization of a micromachined Fabry–Perot vibration sensor for high-temperature applications , 2006 .

[3]  Richard M. White,et al.  Piezoelectric cantilever microphone and microspeaker , 1996 .

[4]  A. Efremov,et al.  Investigation of SrBi2Ta2O9 thin films etching mechanisms in Cl2 /Ar plasma , 2003 .

[5]  Richard S. Muller,et al.  Piezoelectric microphone with on-chip CMOS circuits , 1993 .

[6]  E. S. Kim,et al.  Integration of piezoelectric tunable capacitors and bonded-wire inductors for contactless RF switch and tunable filter , 2011 .

[7]  Wouter Olthuis,et al.  A review of silicon microphones , 1994 .

[8]  R. Muller,et al.  IC-Processed piezoelectric microphone , 1987, IEEE Electron Device Letters.

[9]  Madan Dubey,et al.  Design and Fabrication of a Lead Zirconate Titanate (PZT) Thin Film Acoustic Sensor , 2003 .

[10]  E. S. Kim,et al.  Measurement of piezoelectric strength of ZnO thin films for MEMS applications , 1998 .

[11]  S. Muensit,et al.  Extensional piezoelectric coefficients of gallium nitride and aluminum nitride , 1999 .

[12]  A. J. Sprenkels,et al.  Development of an electret microphone in silicon , 1989 .

[13]  Nicolas Ledermann,et al.  Piezoelectric Pb(Zrx, Ti1−x)O3 thin film cantilever and bridge acoustic sensors for miniaturized photoacoustic gas detectors , 2004 .

[14]  Eun Sok Kim,et al.  Fabrication of piezoelectric acoustic transducers built on cantilever-like diaphragm , 2001, Technical Digest. MEMS 2001. 14th IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.01CH37090).

[15]  D. Schindel,et al.  The design and characterization of micromachined air-coupled capacitance transducers , 1995, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[16]  D. Berlincourt,et al.  Piezoelectric transducer materials , 1965 .

[17]  K. Shung,et al.  A 30-MHz piezo-composite ultrasound array for medical imaging applications , 2002, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.