Measurement of residual stresses in polymeric parts by indentation method
暂无分享,去创建一个
Jae Ryoun Youn | Sung Ho Kim | S. H. Kim | Sungho Kim | S. Kim | J. Youn | Seong Yeol Pak | Seong Yun Kim | S. Pak
[1] R. G. Treuting,et al. A Mechanical Determination of Biaxial Residual Stress in Sheet Materials , 1951 .
[2] D. I. Crecraft. Ultrasonic measurement of stresses , 1968 .
[3] Yang-ming Chang,et al. Residual stress measurement by X-ray diffraction , 1972 .
[4] John H. Underwood,et al. Residual-stress measurement using surface displacements around an indentation , 1973 .
[5] C. Ruud,et al. Residual Stress Measurement by X-Rays: Errors, Limitations and Applications , 1979 .
[6] M. R. James,et al. Quantitative nondestructive measurements of residual stresses , 1980 .
[7] J. R. White,et al. Residual stresses and aging in injection molded polypropylene , 1980 .
[8] C. O. Ruud,et al. A review of selected non-destructive methods for residual stress measurement , 1982 .
[9] A. Isayev,et al. Residual Stress Development in the Injection Molding of Polymers , 1984 .
[10] H. H. Chiang,et al. Postmolding and load‐induced deformation analysis of plastic parts in the injection molding process , 1991 .
[11] G. Pharr,et al. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments , 1992 .
[12] Christopher W. Macosko,et al. Rheology: Principles, Measurements, and Applications , 1994 .
[13] T. Osswald,et al. Materials Science of Polymers for Engineers , 1995 .
[14] J. Youn,et al. Characterization of deformation in injection molded parts after packing and cooling , 1999 .
[15] Jae Ryoun Youn,et al. Shrinkage Analysis of Molded Parts Using Neural Network , 1999 .
[16] Michael B. Prime,et al. Residual Stress Measurement by Successive Extension of a Slot: The Crack Compliance Method , 1999 .
[17] M. Bhattacharya,et al. Residual stresses and density gradient in injection molded starch/synthetic polymer blends , 2000 .
[18] P. Withers,et al. Residual stress. Part 1 – Measurement techniques , 2001 .
[19] K. Stelson,et al. APPROXIMATE MODEL OF THERMAL RESIDUAL STRESS IN AN INJECTION MOLDED PART , 2002 .
[20] A. Turnbull,et al. Measurement of residual stress in engineering plastics using the hole-drilling technique. , 2003 .
[21] D. Kwon,et al. Estimation of biaxial surface stress by instrumented indentation with sharp indenters , 2004 .
[22] Wen-Bin Young,et al. Study on residual stresses of thin-walled injection molding , 2005 .
[23] E. Olivas,et al. Nanoindentation measurement of surface residual stresses in particle-reinforced metal matrix composites , 2006 .
[24] C. Cané,et al. FIB-based technique for stress characterization on thin films for reliability purposes , 2007 .
[25] Jae Ryoun Youn,et al. Determination of residual stresses in injection-moulded flat plate : Simulation and experiments , 2007 .
[26] S. H. Kim,et al. Molded geometry and viscoelastic behavior of film insert molded parts , 2008 .
[27] Seung‐Hwan Lee,et al. Thermoviscoelastic Behavior of Film‐Insert‐Molded Parts Prepared under Various Processing Conditions , 2008 .
[28] S. H. Kim,et al. Measurement of residual stresses in film insert molded parts with complex geometry , 2009 .
[29] Jae Ryoun Youn,et al. Effects of film and substrate dimensions on warpage of film insert molded parts , 2010 .
[30] S. H. Kim,et al. Residual stress and viscoelastic deformation of film insert molded automotive parts , 2010 .
[31] S. H. Kim,et al. Residual Stresses and Thermoviscoelastic Deformation of Laminated Film Prepared for Film Insert Molding , 2012 .