Liquid holdup measurement in horizontal oil–water two-phase flow by using concave capacitance sensor

Abstract Due to the complex flow structures of horizontal oil–water flows, the liquid holdup measurement is still a challenging problem. In this paper, we using the finite element analysis build a two-dimensional model of the concave capacitance sensor and investigate the effect of sensor geometry on the distribution of the sensitivity field. Through calculating the sensor static response for different horizontal oil–water flow patterns, we figure out the optimum geometry of the concave capacitance sensor. In addition, we conduct experiment to obtain the measured response of the concave capacitance sensor and achieve the oil-holdup by using quick closing valve. The results indicate that the optimized concave capacitance sensor shows good performance for liquid holdup measurement of horizontal oil–water two-phase flow.

[1]  Jiamin Ye,et al.  Optimization of Helical Capacitance Sensor for Void Fraction Measurement of Gas-Liquid Two-Phase Flow in a Small Diameter Tube , 2011, IEEE Sensors Journal.

[3]  A new principle for designing optimal capacitive void fraction sensors applied to a rod-bundle geometry , 1995 .

[4]  E. Hammer,et al.  Capacitance Transducers for Non-intrusive Measurement of Water in Crude Oil , 1989 .

[5]  Jiamin Ye,et al.  Helical Capacitance Sensor-Based Gas Fraction Measurement of Gas–Liquid Two-Phase Flow in Vertical Tube With Small Diameter , 2011, IEEE Sensors Journal.

[6]  Maurice Beck,et al.  Design of capacitance electrodes for concentration measurement of two-phase flow , 1990 .

[7]  Rakesh Mishra,et al.  Measurement of bubble velocity components in a swirling gas–liquid pipe flow using a local four-sensor conductance probe , 2005 .

[8]  James P. Brill,et al.  A Study of Oil-Water Flow Patterns in Horizontal Pipes , 1996 .

[9]  Arnout Willockx,et al.  Capacitance signal analysis of horizontal two-phase flow in a small diameter tube , 2008 .

[10]  Ningde Jin,et al.  The development of a conductance method for measuring liquid holdup in horizontal oil?water two-phase flows , 2012 .

[11]  Wuqiang Yang,et al.  Hardware design of electrical capacitance tomography systems , 1996 .

[12]  Mahmoud Meribout,et al.  A new hierarchical reconstruction algorithm for electrical capacitance tomography using a relaxation region-based approach , 2012 .

[13]  Josua P. Meyer,et al.  Horizontal two-phase flow characterization for small diameter tubes with a capacitance sensor , 2007 .

[14]  E. A. Hammer,et al.  Capacitance sensor design for reducing errors in phase concentration measurements , 1998 .

[15]  Vittorio Ferrari,et al.  Capacitance sensor for hold-up measurement in high-viscous-oil/conductive-water core-annular flows , 2011 .

[16]  M. Sami A. Abouelwafa,et al.  The Use of Capacitance Sensors for Phase Percentage Determination in Multiphase Pipelines , 1980, IEEE Transactions on Instrumentation and Measurement.

[17]  J. C. Borst,et al.  A CAPACITANCE SENSOR FOR TWO-PHASE VOID FRACTION MEASUREMENT AND FLOW PATTERN IDENTIFICATION , 1988 .

[19]  Vittorio Ferrari,et al.  A capacitive sensor system for the analysis of two-phase flows of oil and conductive water , 2010 .

[20]  P. Poesio,et al.  Experimental investigation on two-phase air/high-viscosity-oil flow in a horizontal pipe , 2011 .

[21]  Bernd Ameel,et al.  Flow regime based calibration of a capacitive void fraction sensor for small diameter tubes , 2013 .

[22]  Maurice Beck,et al.  Conductivity effects on capacitance measurements of two-component fluids using the charge transfer method , 1988 .