Optimization of friction and wear behaviour of Al–Si 3 N 4 nano composite and Al–Gr–Si 3 N 4 hybrid composite under dry sliding conditions

Abstract The tribological behaviour of gravity die stir cast LM6 alloy with graphite (Gr) and silicon nitride nanoparticles was investigated. Al–Gr–Si 3 N 4 hybrid composite, Al–Si 3 N 4 nanocomposite and Al–Gr nanocomposites were separately fabricated to investigate their frictional and wear characteristics under dry sliding conditions. EDS was used to ensure the uniform presence of nano Si 3 N 4 and graphite in the cast. L9 orthogonal array method was chosen to conduct the experiments to study the effect of different applied loads (20, 30 and 40 N) and sliding distances (1, 2 and 3 km). The results showed that the respective wear rate and coefficient of friction (COF) decreased by 25% and 15% for hybrid composite when compared with those of Al–Si 3 N 4 nanocomposite whereas the wear rate and COF of Al–Gr was found to be very minimal. The micro Vickers hardness of the hybrid composite was 14% more than that of the simple nanocomposite and there was not much notable variation for Al–Gr and Al–Si 3 N 4 nanocomposite materials. Scanning electron microscope was used to analyze the worn surface and subsurface, from which it was noted that the predominant wear mechanisms observed were abrasive for nanocomposite and both abrasive and adhesive mechanism for hybrid composite. Analysis of variance (ANOVA) and F -test were used to check the validity model and to determine the significant parameters affecting the wear rates.

[1]  R. N. Rao,et al.  The effect of wear parameters and heat treatment on two body abrasive wear of Al–SiC–Gr hybrid composites , 2016 .

[2]  S. C. Vettivel,et al.  Experimental investigation on mechanical behaviour, modelling and optimization of wear parameters of B4C and graphite reinforced aluminium hybrid composites , 2014 .

[3]  Wenshu Yang,et al.  Effect of volume fraction on microstructure and mechanical properties of Si3N4/Al composites , 2011 .

[4]  Csaba Balázsi,et al.  Wear damage of Si3N4-graphene nanocomposites at room and elevated temperatures , 2014 .

[5]  Chuanzhen Huang,et al.  Friction and wear behaviors of Al2O3/TiC micro-nano-composite ceramic sliding against metals and hard materials , 2016 .

[6]  T. Cygan,et al.  Influence of graphene addition and sintering temperature on physical properties of Si3N4 matrix composites , 2016 .

[7]  L. Kumaraswamidhas,et al.  High temperature investigation on EDM process of Al 2618 alloy reinforced with Si3N4, ALN and ZrB2 in-situ composites , 2016 .

[8]  N. Sateesh,et al.  Manufacture of Aluminium Metal Matrix Composite (Al7075-SiC) by Stir Casting Technique☆ , 2015 .

[9]  D. Khanduja,et al.  Production and some properties of Si3N4 reinforced aluminium alloy composites , 2015 .

[10]  Houan Zhang,et al.  Effect of Si3N4 content on microstructures and antioxidant properties of MoSi2/Si3N4 composite coatings on Mo substrate , 2015 .

[11]  G. Ugrasen,et al.  Hardness and Wear Characteristics of Hybrid Aluminium Metal Matrix Composites Produced by Stir Casting Technique , 2015 .

[12]  A. I. Bazlov,et al.  Microstructure and material characterization of 6063/B4C and 1545K/B4C composites produced by two stir casting techniques for nuclear applications , 2016 .

[13]  M. Tajally,et al.  Fabrication and characteristic of Al-based hybrid nanocomposite reinforced with WO3 and SiC by accumulative roll bonding process , 2015 .

[14]  Xuefei Huang,et al.  Microstructure and mechanical properties of Ni-P-Si3N4 nanowire electroless composite coatings , 2015 .

[15]  Yizhong Huang,et al.  Investigation of microstructure and mechanical properties of Al6061-nanocomposite fabricated by stir casting , 2014 .

[16]  K. Alaneme,et al.  Corrosion and wear behaviour of Al-Mg-Si alloy matrix hybrid composites reinforced with rice husk ash and silicon carbide , 2014 .