Experimental and theoretical analysis of an aluminum foam enhanced phase change thermal storage unit

Abstract This paper investigates heat transfer enhancement of a shell-and-tube latent heat thermal storage unit, using water as the phase change material, by addition of open-cell aluminum foam. Two shell-and-tube thermal storage units were designed and fabricated such that they were identical except for the inclusion of aluminum foam in one unit. The experimental results indicated that the foam significantly increased the heat transfer during both solidification and melting, as characterized by the overall heat transfer coefficient. The relative enhancement was greater for melting than solidification due to the lower thermal conductivity of liquid water relative to ice. It was also observed that natural convection during melting was suppressed by the foam but that this suppression was still outweighed by the thermal conductance enhancement. Using a semi-analytical approach to model the coupled phase change and forced convection heat transfer, best-fit effective thermal conductivities for the water–foam composite were determined to be 1.8 W/m-K during melting and 5.1 W/m-K during solidification. The value obtained in this work for melting is significantly lower than predictions from existing effective thermal conductivity models for foam composites, and as is shown, the impact of this discrepancy on the overall thermal performance of the thermal storage unit is significant. The value obtained for solidification is also less than that predicted by the same thermal conductivity models; however, for solidification, the impact of this discrepancy is smaller. The discrepancies between values obtained in this work and effective thermal conductivity models is attributed to local thermal non-equilibrium, which is more severe during melting than solidification due to the lower thermal conductivity of liquid water relative to ice. This finding is further demonstrated by numerical investigation of phase change in a representative composite material containing a foam-like structure modeled on the well-known Kelvin cell.

[1]  A. K. da Silva,et al.  Numerical Optimization and Power Output Control of a Hot Thermal Battery with Phase Change Material , 2014 .

[2]  Zhenyu Liu,et al.  Numerical modeling for solid–liquid phase change phenomena in porous media: Shell-and-tube type latent heat thermal energy storage , 2013 .

[3]  D. Hasselman,et al.  Effective Thermal Conductivity of Composites with Interfacial Thermal Barrier Resistance , 1987 .

[4]  Philippe Marty,et al.  Experimental and numerical study of annular PCM storage in the presence of natural convection , 2013 .

[5]  Yuwen Zhang,et al.  Semi-analytical solution of thermal energy storage system with conjugate laminar forced convection , 1996 .

[6]  Luisa F. Cabeza,et al.  Review on phase change materials (PCMs) for cold thermal energy storage applications , 2012 .

[7]  Mahmoud Moeini Sedeh,et al.  Thermal conductivity improvement of phase change materials/graphite foam composites , 2013 .

[8]  Karthik K. Bodla,et al.  Resistance network-based thermal conductivity model for metal foams , 2010 .

[9]  J. Murthy,et al.  A Two-Temperature Model for Solid/Liquid Phase Change in Metal Foams , 2005 .

[10]  Francis Agyenim,et al.  A review of materials, heat transfer and phase change problem formulation for latent heat thermal energy storage systems (LHTESS) , 2010 .

[11]  D. Poulikakos,et al.  On the effective thermal conductivity of a three-dimensionally structured fluid-saturated metal foam , 2001 .

[12]  Dan Zhou,et al.  Experimental investigations on heat transfer in phase change materials (PCMs) embedded in porous materials , 2011 .

[13]  Sung-Tae Hong,et al.  Effects of Surface Area Density of Aluminum Foams on Thermal Conductivity of Aluminum Foam‐Phase Change Material Composites , 2007 .

[14]  Wei Li,et al.  The effect of pore size and porosity on thermal management performance of phase change material infiltrated microcellular metal foams , 2014 .

[15]  Michael T. Heath,et al.  Scientific Computing: An Introductory Survey , 1996 .

[16]  Liwu Fan,et al.  Thermal conductivity enhancement of phase change materials for thermal energy storage: A review , 2011 .

[17]  Kamil Kaygusuz,et al.  Thermal energy storage performance of paraffin in a novel tube-in-shell system , 2008 .

[18]  L. Cabeza,et al.  Heat and cold storage with PCM: An up to date introduction into basics and applications , 2008 .

[19]  R. Ruoff,et al.  Enhanced thermal conductivity of phase change materials with ultrathin-graphite foams for thermal energy storage , 2014 .

[20]  R. Mahajan,et al.  The Effective Thermal Conductivity of High Porosity Fibrous Metal Foams , 1999 .

[21]  W. Lu,et al.  Heat transfer enhancement for thermal energy storage using metal foams embedded within phase change materials (PCMs) , 2010 .

[22]  M. Lacroix.  Numerical simulation of a shell-and-tube latent heat thermal energy storage unit , 1993 .

[23]  A. Sharma,et al.  Review on thermal energy storage with phase change materials and applications , 2009 .

[24]  Juan Shi,et al.  Experimental and numerical study on melting of phase change materials in metal foams at pore scale , 2014 .

[25]  X. Py,et al.  Paraffin/porous-graphite-matrix composite as a high and constant power thermal storage material , 2001 .

[26]  Francis Agyenim,et al.  Modeling of Thermal Energy Storage Shell-and-Tube Heat Exchanger , 2014 .

[27]  Anica Trp,et al.  An experimental and numerical investigation of heat transfer during technical grade paraffin melting and solidification in a shell-and-tube latent thermal energy storage unit , 2005 .

[28]  Mete Avci,et al.  Experimental study of thermal energy storage characteristics of a paraffin in a horizontal tube-in-shell storage unit , 2013 .

[29]  A. Faghri,et al.  Performance characteristics of a thermal energy storage module - A transient PCM/forced convection conjugate analysis , 1991 .

[30]  Kamal Abdel Radi Ismail,et al.  Performance of a thermal storage system of the vertical tube type , 2000 .

[31]  Kamal Abdel Radi Ismail,et al.  Thermal performance of a pcm storage unit , 1999 .

[32]  Robert Lemlich,et al.  A theory for the limiting conductivity of polyhedral foam at low density , 1978 .

[33]  A. Sari,et al.  Thermal energy storage system using stearic acid as a phase change material , 2001 .

[34]  Ming Li,et al.  Effective thermal conductivity of open-cell metal foams impregnated with pure paraffin for latent heat storage , 2014 .

[35]  R. Mahajan,et al.  Thermophysical properties of high porosity metal foams , 2002 .

[36]  M. Conti,et al.  Transient behaviour analysis of a latent heat thermal storage module , 1993 .

[37]  M. Kaviany.  Principles of heat transfer in porous media , 1991 .

[38]  Wenhua Yu,et al.  Heat transfer analysis of a latent heat thermal energy storage system using graphite foam for concentrated solar power , 2014 .

[39]  W. Tao,et al.  Experimental and numerical studies on melting phase change heat transfer in open-cell metallic foams filled with paraffin , 2012 .

[40]  Li Shi,et al.  Thermodynamic model of a thermal storage air conditioning system with dynamic behavior , 2013 .

[41]  A. Elgafy,et al.  Numerical Study for Enhancing the Thermal Conductivity of Phase Change Material (PCM) Storage using High Thermal Conductivity Porous Matrix , 2005 .

[42]  J. Selman,et al.  Thermal conductivity enhancement of phase change materials using a graphite matrix , 2006 .

[43]  J. Hyun,et al.  Effective Thermal Conductivity and Permeability of Aluminum Foam Materials1 , 2000 .

[44]  C. Nan,et al.  Effective thermal conductivity of particulate composites with interfacial thermal resistance , 1997 .

[45]  Ya-Ling He,et al.  Numerical study on thermal energy storage performance of phase change material under non-steady-state inlet boundary , 2011 .

[46]  K. Lafdi,et al.  Experimental Study on the Influence of Foam Porosity and Pore Size on the Melting of Phase Change Materials , 2007 .

[47]  Francis Agyenim,et al.  Heat transfer enhancement in medium temperature thermal energy storage system using a multitube heat transfer array , 2010 .

[48]  Changying Zhao,et al.  A numerical investigation of heat transfer in phase change materials (PCMs) embedded in porous metals , 2011 .

[49]  Ahmed Elgafy,et al.  Graphite foams infiltrated with phase change materials as alternative materials for space and terrestrial thermal energy storage applications , 2008 .

[50]  Kambiz Vafai,et al.  On departure from local thermal equilibrium in porous media due to a rapidly changing heat source: The Sparrow number , 1999 .