Experimental Analysis of 1-3 Piezocomposites for High-Intensity Focused Ultrasound Transducer Applications

Piezocomposites with 1-3 connectivity have been extensively used in medical imaging transducers and high-intensity focused ultrasound transducers, but most studies of 1-3 piezocomposites address medical imaging applications. The purpose of this study was to completely investigate 1-3 composites specifically for high-power ultrasonic transducer applications via a series of experimental analyses. PZT4-epoxy composite focused transducers with various aspect ratios and volume fractions were constructed in-house for the evaluation of the coupling factor, dielectric loss tangent, quality factor, bandwidth, acoustic impedance, and electroacoustic efficiency. The experimental analyses demonstrated that although the coupling factor of composite transducers was higher than that of the ceramic transducer, the composite transducers had a lower efficiency due to the high dielectric loss and high mechanical energy loss of the composites. In addition, the bandwidth and acoustic impedance of composite transducers were superior to the ceramic transducer. For the composite transducers, the efficiency and acoustic impedance were inversely proportional to the aspect ratio and linearly proportional to the volume fraction. The coupling of inter pillars that are too close to each other could cause a significant decrease in the efficiency of the composite transducer. With an appropriate design in terms of the aspect ratio, volume fraction, and PZT-pillar spacing, a high-efficiency composite high-intensity focused ultrasound transducer can be achieved.

[1]  L. E. Cross,et al.  Piezoelectric Composite Materials for Ultrasonic Transducer Applications. Part I: Resonant Modes of Vibration of PZT Rod-Polymer Composites , 1985, IEEE Transactions on Sonics and Ultrasonics.

[2]  Mathieu Pernot,et al.  3-D real-time motion correction in high-intensity focused ultrasound therapy. , 2004, Ultrasound in medicine & biology.

[3]  Volume Su.  IEEE Standard on Piezoelectricity , 1984 .

[4]  Emad S Ebbini,et al.  Dual-Mode Ultrasound Phased Arrays for Image-Guided Surgery , 2006, Ultrasonic imaging.

[5]  H. Fan,et al.  The role of piezoelectric rods in 1–3 composite for the hydrostatic response applications , 2006 .

[6]  W. Marsden.  I and J , 2012 .

[7]  T. Ritter,et al.  1-3 piezoelectric composites for high power ultrasonic transducer applications , 1999, 1999 IEEE Ultrasonics Symposium. Proceedings. International Symposium (Cat. No.99CH37027).

[8]  G. Fleury,et al.  High intensity therapeutic ultrasound transducer performance and characterisation , 2010, 2010 IEEE International Ultrasonics Symposium.

[9]  B. Auld,et al.  Modeling 1-3 composite piezoelectrics: thickness-mode oscillations , 1991, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[10]  G. Hayward,et al.  Assessing the influence of pillar aspect ratio on the behavior of 1-3 connectivity composite transducers , 1996, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[11]  J. V. Biggers,et al.  Composites of PZT and Epoxy for Hydrostatic Transducer Applications , 1981 .

[12]  Roger G. Jackson,et al.  Novel Sensors and Sensing , 2004 .

[13]  R. Holland,et al.  Representation of Dielectric, Elastic, and Piezoelectric Losses by Complex Coefficients , 1967, IEEE Transactions on Sonics and Ultrasonics.

[14]  L. E. Cross,et al.  Connectivity and piezoelectric-pyroelectric composites , 1978 .

[15]  J Y Chapelon,et al.  New piezoelectric transducers for therapeutic ultrasound. , 2000, Ultrasound in medicine & biology.

[16]  J. Galt,et al.  Ultrasonic propagation in liquids : I. Application of pulse technique to velocity and absorption measurements at 15 megacycles , 1946 .

[17]  G Fleury,et al.  Dual-mode transducers for ultrasound imaging and thermal therapy. , 2010, Ultrasonics.