Computer modelling and experimental investigation of building integrated sub-wet bulb temperature evaporative cooling system

The paper presents computer modelling and laboratory experiment results of a sub-wet bulb temperature indirect evaporative cooling system for space cooling in buildings. The prototype employs hollow porous ceramic water containers as wet media material for water evaporation. The cooled air is delivered without increasing its moisture content. The performance of the cooler was evaluated using a computer model, and the results of which were validated experimentally. The cooling capacity and effectiveness of the cooler were evaluated at inlet air dry bulb temperature of 30 and 35°C and relative humidity ranging from 35% to 50%. It was found that the cooler can supply air for space cooling at sub-wet bulb temperature conditions; achieve measured cooling capacity approaching 225 W/m2 of exposed ceramic material wet surface area and wet bulb effectiveness higher than unity. The high thermal performance of the constructed evaporative cooler indicates the system could be a potential substitute to conventional mechanical air-conditioning systems in buildings in many parts of the world where hot and dry climatic conditions prevail.

[1]  Faleh A. Al-Sulaiman,et al.  Evaluation of the performance of local fibers in evaporative cooling , 2002 .

[2]  W Wim Zeiler,et al.  Performance model for small scale indirect evaporative Cooler. , 2007 .

[3]  Ala Hasan.  Indirect evaporative cooling of air to a sub-wet bulb temperature , 2010 .

[4]  Gert Jan Foster Robert Dijkstra Ebel Tummers Marja Bom,et al.  Evaporative Air-Conditioning: Applications for Environmentally Friendly Cooling , 1999 .

[5]  Saffa Riffat,et al.  Mathematical model of indirect evaporative cooler using porous ceramic and heat pipe , 2004 .

[6]  T. Habeebullah,et al.  Thermal Performance and Environmental Assessment of Evaporative Cooling Systems: Case of Mina Valley, Saudi Arabia , 2014 .

[7]  Dae-Young Lee,et al.  Experimental study of a counter flow regenerative evaporative cooler with finned channels , 2013 .

[8]  Ala Hasan,et al.  Indirect evaporative cooling : Past, present and future potentials , 2012 .

[9]  W. P. Jones,et al.  Air Conditioning Engineering , 1967 .

[10]  Luis Pérez-Lombard,et al.  A review of HVAC systems requirements in building energy regulations , 2011 .

[11]  Shailesh Kumar,et al.  Numerical study of a novel dew point evaporative cooling system , 2010 .

[12]  Takahiko Miyazaki,et al.  The cooling performance of a building integrated evaporative cooling system driven by solar energy , 2011 .

[13]  Ghassem Heidarinejad,et al.  Numerical study of regenerative evaporative coolers for sub-wet bulb cooling with cross- and counter-flow configuration , 2015 .

[14]  Ambrose Dodoo,et al.  Building energy-efficiency standards in a life cycle primary energy perspective , 2011 .

[15]  Boris Halasz,et al.  A general mathematical model of evaporative cooling devices , 1998 .

[16]  Frank Bruno,et al.  On-site experimental testing of a novel dew point evaporative cooler , 2011 .

[17]  Mu'azu Musa,et al.  Novel evaporative cooling systems for building applications , 2009 .

[18]  William M. Worek,et al.  Optimization of wet-surface heat exchangers , 1989 .

[19]  K. Nagano,et al.  Experimental study of the performance of porous materials to moderate the roof surface temperature by its evaporative cooling effect , 2009 .

[20]  S. Riffat,et al.  Numerical study of a novel counter-flow heat and mass exchanger for dew point evaporative cooling. , 2008 .

[21]  Saffa Riffat,et al.  Performance of porous ceramic evaporators for building cooling application , 2003 .

[22]  Shailesh Kumar,et al.  An experimental study of a novel dew point evaporative cooling system , 2010 .

[23]  Saffa Riffat,et al.  Comparative study of heat and mass exchanging materials for indirect evaporative cooling systems , 2008 .