Experimental Investigation of Stepped Tip Gap Effects on the Performance of a Transonic Axial-Flow Compressor Rotor

The effects of stepped-tip gaps and clearance levels on the performance of transonic axial-flow compressor rotor were experimentally determined. A two-stage compressor with no inlet guide vanes was tested in a modern transonic compressor research facility. The first-stage rotor was unswept and was tested for an optimum tip clearance with variations in stepped gaps machined into the casing near the aft tip region of the rotor. Nine casing geometries were investigated consisting of three step profiles at each of three clearance levels. For small and intermediate clearances, stepped tip gaps were found to improve pressure ratio, efficiency, and flow range for most operating conditions. At 100 percent design rotor speed, stepped tip gaps produced a doubling of mass flow range with as much as a 2.0 percent increase in mass flow and a 1.5 percent improvement in efficiency. This study provides guidelines for engineers to improve compressor performance for an existing design by applying an optimum casing profile.

[1]  Aspi Rustom Wadia,et al.  The Effect of Tip Clearance on a Swept Transonic Compressor Rotor , 1996 .

[2]  Steen A. Sjolander,et al.  Effects of Simulated Rotation on Tip Leakage in a Planar Cascade of Turbine Blades: Part I—Tip Gap Flow , 1992 .

[3]  Robert F. Kunz,et al.  Investigation of Tip Clearance Phenomena in an Axial Compressor Cascade Using Euler and Navier–Stokes Procedures , 1993 .

[4]  Anton Basson,et al.  Numerical Simulation of Tip Clearance Effects in Turbomachinery , 1995 .

[5]  Edward M. Greitzer,et al.  Numerical simulation of compressor endwall and casing treatment flow phenomena , 1992 .

[6]  H. D. Joslyn,et al.  Throughflow Analysis of a Multistage Compressor Operating at Near-Stall Conditions , 1987 .

[7]  Frank E. Marble,et al.  Similarity analysis of compressor tip clearance flow structure , 1990 .

[8]  Mark L. Celestina,et al.  Experimental and Computational Investigation of the Tip Clearance Flow in a Transonic Axial Compressor Rotor , 1996 .

[9]  A. J. Wennerstrom,et al.  Experimental Study of a High-Throughflow Transonic Axial Compressor Stage , 1984 .

[10]  Edward M. Greitzer,et al.  The Role of Tip Clearance in High-Speed Fan Stall , 1991 .

[11]  Edward J. Hall,et al.  Aerodynamic analysis of compressor casing treatment with a 3-D Navier-Stokes solver , 1994 .

[12]  Steen A. Sjolander,et al.  Effects of Simulated Rotation on Tip Leakage in a Planar Cascade of Turbine Blades: Part II—Downstream Flow Field and Blade Loading , 1992 .

[13]  Chunill Hah,et al.  Characterization of the first-stage rotor in a two-stage transonic compressor , 1995 .

[14]  S. L. Puterbaugh,et al.  Tip clearance flow-shock interaction in a transonic compressor rotor , 1995 .

[15]  Steven L. Puterbaugh,et al.  Tip shock structures in transonic compressor rotors , 1993 .

[16]  R. P. Dring,et al.  Through-Flow Modeling of Axial Turbomachinery , 1986 .

[17]  Edward M. Greitzer,et al.  Closure to “Discussions of ‘The Role of Tip Clearance in High-Speed Fan Stall’” (1993, ASME J. Turbomach., 115, p. 39) , 1993 .

[18]  M. Valenti.  Upgrading jet turbine technology , 1995 .

[20]  C. Hah,et al.  A Numerical Modeling of Endwall and Tip-Clearance Flow of an Isolated Compressor Rotor , 1985 .

[21]  R. Moore,et al.  Rotor tip clearance effects on overall and blade-element performance of axial-flow transonic fan stage , 1982 .