Investigation of ash deposit formation during co-firing of coal with sewage sludge, saw-dust and refuse derived fuel

Abstract Blends of a South African bituminous “Middleburg” coal and alternative fuels (sewage sludge, saw-dust and refuse derived fuel) have been fired in the slagging reactor to examine the effect of the added fuel on slagging propensity of the mixtures. Two ceramic deposition probes have been used to investigate the initial stages of slagging at 1300 °C and 1200 °C, at 0.5 s and 2 s residence times, respectively. The deposition rates and the deposit structures have been different for the two probes used. Substantial impact of sewage sludge has been observed. The initially formed deposits have become rapidly molten and they flow around the deposition probes, particularly when the sewage sludge fraction exceeds 15% by thermal input and the gas flow temperature exceeds the ash melting point. A 5% addition of the refuse derived fuel (RDF) has increased the deposition rate by almost a factor of two. Large RDF ash particles have been observed in the deposits. The slagging propensity has been correlated with the slagging index based on the ratio of fluxing oxides to sintering oxides. Intensive slagging has been observed when the index is in the 0.75–2 range. Moving away from this range in either direction has decreased the slagging intensity.

[1]  Richard W. Bryers,et al.  Fireside slagging, fouling, and high-temperature corrosion of heat-transfer surface due to impurities in steam-raising fuels , 1996 .

[2]  Lian Zhang,et al.  Transformation of mineral and emission of particulate matters during co-combustion of coal with sewage sludge , 2004 .

[3]  M. Hupa,et al.  Deposition behaviour of molten alkali-rich fly ashes—development of a submodel for CFD applications , 2005 .

[4]  J. Tomeczek,et al.  Modelling of deposits formation on heating tubes in pulverized coal boilers , 2004 .

[5]  M. Pourkashanian,et al.  Prediction of ash deposition on superheater tubes from pulverized coal combustion , 1996 .

[6]  RajenderKumar Gupta,et al.  Investigation of coals and blends deposit structure: measuring the deposit bulk porosity using thermomechanical analysis technique , 2005 .

[7]  Peter Glarborg,et al.  Heat transfer in ash deposits: A modelling tool-box , 2005 .

[8]  F. Frandsen,et al.  Characterization of Ashes and Deposits from High-Temperature Coal-Straw Co-Firing , 1999 .

[9]  Mikko Hupa,et al.  Fouling tendency of ash resulting from burning mixtures of biofuels. Part 1: Deposition rates , 2006 .

[10]  K. Cliffe,et al.  Particle deposition simulation using the CFD code FLUENT , 2000 .

[11]  R. Günther,et al.  Verbrennung und Feuerungen , 1974 .

[12]  T. Heinzel,et al.  Investigation of slagging in pulverized fuel co-combustion of biomass and coal at a pilot-scale test facility , 1998 .

[13]  A. Sharma,et al.  Mechanistic prediction of ash deposition in a pilot-scale test facility , 2005 .

[14]  Juhani Ruuskanen,et al.  CO-COMBUSTION OF REFUSE-DERIVED AND PACKAGING-DERIVED FUELS (RDF AND PDF) WITH CONVENTIONAL FUELS , 1997 .

[15]  Marek Pronobis,et al.  The influence of biomass co-combustion on boiler fouling and efficiency , 2006 .

[16]  Larry L. Baxter,et al.  Ash deposition during biomass and coal combustion: A mechanistic approach , 1993 .

[17]  Atul Sharma,et al.  An experimental study of the effect of coal blending on ash deposition , 2004 .

[18]  Chikao Kanaoka,et al.  Combustibility of dried sewage sludge and its mineral transformation at different oxygen content in drop tube furnace , 2004 .