Enhancement of phase-change evaporators with zeotropic refrigerant mixture using metal foams

Abstract Almost all thermal systems use some kind of heat exchanger. In many cases, evaporators are needed for systems such as organic Rankine cycle (ORC) systems. Evaporators contribute to a big portion of the capital cost, and their price is directly related to their size or transfer area. Highly porous open-cell metal foams are being considered to improve performance while keeping the size of heat exchangers small. This study experimentally investigates the degradation of the heat transfer coefficient of zeotropic mixtures during phase change in a plate heat exchanger with metal-foam-filled channels. The working fluids were pure R245fa and a zeotropic mixture of R245fa/R134a (0.6/0.4 molar ratio). The results show that the metal foams significantly increase the recovered heat, overall heat transfer coefficient, and effectiveness of the heat exchanger for mass flux ranging from 90 to 290 kg/m 2 s, but at the expense of increasing the pressure drop. The same improvement was observed for the mixture of refrigerants. The degraded heat transfer coefficient of the mixture compared to the pure refrigerants was recovered by the introduction of metal foams to the system. New correlations are proposed to predict the two-phase heat transfer coefficient of both pure R245fa and the refrigerant mixture in metal foam evaporators.

[1]  Z. Ayub.  Plate Heat Exchanger Literature Survey and New Heat Transfer and Pressure Drop Correlations for Refrigerant Evaporators , 2003 .

[2]  R. Nebbali,et al.  Experimental investigation of convective heat transfer in an open-cell aluminum foams , 2016 .

[3]  S. Kabelac,et al.  Flow boiling of R134a and ammonia in a plate heat exchanger , 2008 .

[4]  Chanhee Moon,et al.  Experimental study on single-phase heat transfer and pressure drop of refrigerants in a plate heat exchanger with metal-foam-filled channels , 2016 .

[5]  Sang Youl Yoon,et al.  Thermal performance of a 10-kW phase-change plate heat exchanger with metal foam filled channels , 2016 .

[6]  Changyun Wen,et al.  Evaporator modeling – A hybrid approach , 2009 .

[7]  Haitao Hu,et al.  Flow boiling of refrigerant in horizontal metal-foam filled tubes: Part 1 – Two-phase flow pattern visualization , 2015 .

[8]  Hubertus Tummescheit,et al.  Moving Boundary Models for Dynamic Simulations of Two-Phase Flows , 2002 .

[9]  Haitao Hu,et al.  Effect of oil on two-phase pressure drop of refrigerant flow boiling inside circular tubes filled with metal foam , 2013 .

[10]  K. Kim,et al.  Flow boiling visualization and heat transfer in metal-foam-filled mini tubes – Part II: Developing predictive methods for heat transfer coefficient and pressure drop , 2016 .

[11]  M. McLinden,et al.  NIST Standard Reference Database 23: Reference Fluid Thermodynamic and Transport Properties-REFPROP, Version 9.1 | NIST , 2013 .

[12]  Kyung Chun Kim,et al.  Flow boiling characteristics of R134a and R245fa mixtures in a vertical circular tube , 2016 .

[13]  Weilin Zhuge,et al.  System design and control for waste heat recovery of automotive engines based on Organic Rankine Cycle , 2016 .

[14]  L. Doretti,et al.  R134a and R1234ze(E) liquid and flow boiling heat transfer in a high porosity copper foam , 2014 .

[15]  Minsung Kim,et al.  Power enhancement potential of a mixture transcritical cycle for a low-temperature geothermal power generation , 2011 .

[16]  J. Navarro-Esbrí,et al.  Boiling heat-transfer coefficient variation for R407C inside horizontal tubes of a refrigerating vapour-compression plant's shell-and-tube evaporator , 2006 .

[17]  Byung Ha Kang,et al.  Flow and heat transfer correlations for porous fin in a plate-fin heat exchanger , 2000 .

[18]  D. P. Sekulic,et al.  Fundamentals of Heat Exchanger Design , 2003 .

[19]  J. Thome.  Prediction of binary mixture boiling heat transfer coefficients using only phase equilibrium data , 1983 .

[20]  R. Winterton,et al.  A general correlation for saturated and subcooled flow boiling in tubes and annuli, based on a nucleate pool boiling equation , 1991 .

[21]  A. Coronas,et al.  Flow boiling heat transfer of ammonia/water mixture in a plate heat exchanger , 2010 .

[22]  K. S. Lee,et al.  Experiments on the characteristics of evaporation of R410A in brazed plate heat exchangers with different geometric configurations , 2003 .

[23]  R. Moffat.  Using Uncertainty Analysis in the Planning of an Experiment , 1985 .

[24]  Tsing-Fa Lin,et al.  Saturated flow boiling heat transfer and pressure drop of refrigerant R-410A in a vertical plate heat exchanger , 2002 .

[25]  L. Doretti,et al.  Low-GWP refrigerants flow boiling heat transfer in a 5 PPI copper foam , 2015 .

[26]  Kyung Chun Kim,et al.  Experimental study of a 1 kw organic Rankine cycle with a zeotropic mixture of R245fa/R134a , 2015 .

[27]  Y. Y. Hsieh,et al.  Subcooled flow boiling heat transfer of R-134a and the associated bubble characteristics in a vertical plate heat exchanger , 2002 .

[28]  S. Ergun,et al.  Fluid Flow through Randomly Packed Columns and Fluidized Beds , 1949 .

[29]  Anthony M. Jacobi,et al.  Summary and evaluation on single-phase heat transfer enhancement techniques of liquid laminar and turbulent pipe flow , 2015 .

[30]  B. Thonon,et al.  Recent Research and Developments in Plate Heat Exchangers , 1995 .

[31]  Claudio Zilio,et al.  Heat transfer during air flow in aluminum foams , 2010 .

[32]  H. Ross,et al.  Horizontal flow boiling of pure and mixed refrigerants , 1987 .

[33]  Morten Willatzen,et al.  A general dynamic simulation model for evaporators and condensers in refrigeration. Part I: moving-boundary formulation of two-phase flows with heat exchange , 1998 .

[34]  Sang Youl Yoon,et al.  Effect of ligament hollowness on heat transfer characteristics of open-cell metal foam , 2016 .

[35]  Ulrich Grigull,et al.  Heat Transfer in Boiling , 1977 .

[36]  S. D. Probert,et al.  Thermal-design data for evaporators of ORC engines utilising low-temperature heat sources , 1990 .

[37]  Andrea Gasparella,et al.  Refrigerant R134a vaporisation heat transfer and pressure drop inside a small brazed plate heat exchanger , 2007 .

[38]  K. Kim,et al.  Effect of gravity vector on flow boiling heat transfer, flow pattern map, and pressure drop of R245fa refrigerant in mini tubes , 2016 .

[39]  G. Longo,et al.  Heat transfer and pressure drop during HFC refrigerant vaporisation inside a brazed plate heat exchanger , 2007 .

[40]  Claudio Zilio,et al.  Pressure drop during air flow in aluminum foams , 2010 .

[41]  H. Lee,et al.  Heat transfer correlation for boiling flows in small rectangular horizontal channels with low aspect ratios , 2001 .

[42]  Haitao Hu,et al.  Flow boiling of refrigerant in horizontal metal-foam filled tubes: Part 2 – A flow-pattern based prediction method for heat transfer , 2015 .

[43]  Denis Clodic,et al.  Modelica-based modelling and simulation of dry-expansion shell-and-tube evaporators working with alternative refrigerant mixtures , 2011 .

[44]  K. Kim,et al.  Flow boiling visualization and heat transfer in metal-foam-filled mini tubes – Part I: Flow pattern map and experimental data , 2016 .

[45]  R. Mahajan,et al.  Forced Convection in High Porosity Metal Foams , 2000 .