On the repair of a cracked beam with a piezoelectric patch

In this paper, the repair of a cracked beam under an external load, employing the electro-mechanical characteristic of the piezoelectric material to induce a local moment, is presented. Conceptually, an external voltage is applied to actuate a piezoelectric patch bonded on the beam to effect closure of the crack so that the singularity induced by the crack tip may be eliminated. Using a simply supported beam as an illustration, the actuation voltage required is obtained from an equation containing variables such as the applied force, and the geometric and material properties of the beam and the piezoelectric material. It is shown mathematically and numerically that the voltage required (a) decreases linearly as the distance between the force and the location of the crack is increased, (b) varies quadratically with the position of the crack along the length of the beam, and (c) decreases hyperbolically as the ratio of the thickness of the piezoelectric patch to that of the beam increases.

[1]  S. Quek,et al.  Sensitivity analysis of crack detection in beams by wavelet technique , 2001 .

[2]  Roger Ohayon,et al.  Finite element modelling of hybrid active–passive vibration damping of multilayer piezoelectric sandwich beams—part I: Formulation , 2001 .

[3]  D. P. Rooke,et al.  Analysis of patched and stiffened cracked panels using the boundary element method , 1992 .

[4]  Dongchang Sun,et al.  Distributed Piezoelectric Element Method for Vibration Control of Smart Plates , 1997 .

[5]  Dimitris A. Saravanos,et al.  Coupled Layerwise Analysis of Composite Beams with Embedded Piezoelectric Sensors and Actuators , 1995 .

[6]  Jiashi Yang,et al.  Equations for the flexural motion of elastic plates with partially electroded piezoelectric actuators , 1997 .

[7]  Chien-chang Lin,et al.  Static shape control of smart beam plates laminated with sine sensors and actuators , 1999 .

[8]  R. J. Callinan,et al.  A design study in crack patching , 1981 .

[9]  E. Crawley,et al.  Use of piezoelectric actuators as elements of intelligent structures , 1987 .

[10]  C. Chue,et al.  Bonded repair of a plate with inclined central crack under biaxial loading , 1994 .

[11]  C. T. Sun,et al.  Analysis of cracked aluminum plates repaired with bonded composite patches , 1995 .

[12]  Francis C. Moon,et al.  Modal Sensors/Actuators , 1990 .

[13]  D. Rooke,et al.  The boundary element method for analysing repair patches on cracked finite sheets , 1988, The Aeronautical Journal (1968).

[14]  Ding Haojiang,et al.  General solutions for coupled equations for piezoelectric media , 1996 .

[15]  P. Cawley,et al.  The rapid monitoring of structures using interdigital Lamb wave transducers , 2000 .

[16]  S. T. Quek,et al.  Dispersion Relations in Piezoelectric Coupled Beams , 2000 .

[17]  David B. Bogy,et al.  A two-dimensional theory for piezoelectric layers used in electro-mechanical transducers—I: Derivation , 1980 .

[18]  Xiaomin Deng,et al.  Damage detection with spatial wavelets , 1999 .

[19]  W. Ostachowicz,et al.  Modelling and vibration analysis of a cantilever composite beam with a transverse open crack , 1995 .

[20]  Nagi G. Naganathan,et al.  Study of induced strain transfer in piezoceramic smart material systems , 1999 .

[21]  Vijay K. Varadan,et al.  Microsensors, microelectromechanical systems (MEMS), and electronics for smart structures and systems , 2000 .

[22]  L. Rose.  An application of the inclusion analogy for bonded reinforcements , 1981 .