Post-cracking behaviour of steel and macro-synthetic fibre-reinforced concretes

Abstract The present paper describes the results of an experimental investigation on the performances of concrete specimens reinforced with either steel or macro-synthetic fibres under three-point bending. Steel fibres are often used to improve the flexural toughness of concrete and are used in various structural applications while synthetic fibres are more often used to reduce crack opening due to shrinkage. Macro-synthetic fibres have been proposed more recently with the aim of creating an alternative to steel fibres in structural applications but their use is still limited. In the tests performed, specimens cast with the same concrete mix, but containing different dosages of either steel or macro-synthetic fibres, were used and compared. In general steel fibres were more efficient in increasing the toughness of concrete than macro-synthetic fibres, even though their results were significantly more scattered. Test results were used to calculate the parameters of stress-crack opening relations via inverse analysis using a cracked hinge model. This numerical model provided results, in terms of force-Crack Mouth Opening Displacement (CMOD) curves, in very good agreement with the experimental data.

[1]  Alberto Meda,et al.  Steel Fiber Concrete Slabs on Ground: A Structural Matter , 2006 .

[2]  Nemkumar Banthia,et al.  Toughness enhancement in steel fiber reinforced concrete through fiber hybridization , 2007 .

[3]  Arne Hillerborg,et al.  Analysis of fracture by means of the fictitious crack model, particularly for fibre reinforced concrete , 1980 .

[4]  Lucie Vandewalle,et al.  Recommendations of RILEM TC 162-TDF: test and design methods for steel fibre reinforced concrete. Design of steel fibre reinforced concrete using the sigma-w method: principles and applications , 2000 .

[5]  Lucie Vandewalle,et al.  Fibre reinforced concrete: new design perspectives , 2009 .

[6]  E. S. Bernard.  Correlations in the behaviour of fibre reinforced shotcrete beam and panel specimens , 2002 .

[7]  Henrik Stang,et al.  New production processes, materials and calculation techniques for fiber reinforced concrete pipes , 1997 .

[8]  P. Rossi.  A model for cracking in fibre-reinforced concrete structures , 1999 .

[9]  Ravindra Gettu,et al.  Fiber Concrete Tunnel Lining , 2006 .

[10]  E. J. Place Hansen,et al.  Round-robin analysis of the RILEM TC 162-TDF beam-bending test: Part 3—Fibre distribution , 2003 .

[11]  Liberato Ferrara,et al.  Relationships between fibre distribution, workability and the mechanical properties of SFRC applied to precast roof elements , 2005 .

[12]  B. I. G. Barr,et al.  A four-exponential model to describe the behaviour of fibre reinforced concrete , 2004 .

[13]  P. Rossi,et al.  Analysis of metallic fibre-reinforced concrete beams submitted to bending , 1996 .

[14]  H. Stang,et al.  Round-robin analysis of the RILEM TC 162-TDF uni-axial tensile test: Part 2 , 2003 .

[15]  R. Gettu,et al.  Study of the distribution and orientation of fibers in SFRC specimens , 2005 .

[16]  Joost C. Walraven,et al.  High performance fiber reinforced concrete: progress in knowledge and design codes , 2009 .

[17]  V. S. Gopalaratnam,et al.  On the characterization of flexural toughness in fiber reinforced concretes , 1995 .

[18]  John Forbes Olesen,et al.  Fictitious Crack Propagation in Fiber-Reinforced Concrete Beams , 2001 .

[19]  E. J. Place Hansen,et al.  Round-robin analysis of the RILEM TC 162-TDF beam-bending test: Part 2—Approximation of δ from the CMOD response , 2003 .

[20]  Simon A. Austin,et al.  Pull-out behaviour of hooked steel fibres , 2002 .

[21]  B. I. G. Barr,et al.  Round-robin analysis of the RILEM TC 162-TDF beam-bending test: Part 1—Test method evaluation , 2003 .

[22]  Lucie Vandewalle,et al.  RILEM TC162-TDF : Test and Design Methods for Steel Fibre Reinforced Concrete : Bending Test, "Technical Recommendation" , 2002 .

[23]  Peter Jones,et al.  Prediction of steel fibre reinforced concrete under flexure from an inferred fibre pull-out response , 2005 .

[24]  Lucie Vandewalle,et al.  Design of steel fibre reinforced concrete using the σ-w method: principles and applications , 2002 .

[25]  Lucie Vandewalle,et al.  RILEM TC 162-TDF: Test and design methods for steel fibre reinforced concrete' - sigma-epsilon-design method - Final Recommendation , 2003 .

[26]  Parviz Soroushian,et al.  DISTRIBUTION AND ORIENTATION OF FIBERS IN STEEL FIBER REINFORCED CONCRETE , 1990 .

[27]  Joaquim A. O. Barros,et al.  Post-cracking behaviour of steel fibre reinforced concrete , 2003 .

[28]  Simon A. Austin,et al.  Predicting the flexural load–deflection response of steel fibre reinforced concrete from strain, crack-width, fibre pull-out and distribution data , 2008 .

[30]  Alberto Meda,et al.  Design Aspects on Steel Fiber-Reinforced Concrete Pavements , 2008 .