Reduction of bridge dynamic amplification through adjustment of vehicle suspension damping

Abstract This paper presents a novel approach to the reduction of short-span bridge dynamic responses to heavy vehicle crossing events. The reductions are achieved through adjustment of the vehicle suspension damping coefficient just before the crossing. Given pre-calculations of the response of a vehicle–bridge system to a set of ‘unit’ road disturbances, it is shown that a single optimum damping coefficient may be determined for a given velocity and any specified road profile. This approach can facilitate implementation since the optimum damping is selected prior to the bridge and there is no need to continuously vary the damping coefficient during the crossing. The concept is numerically validated using a bridge–vehicle interaction model with several road profiles, both measured and artificially generated. The bridge-friendly damping control strategy is shown to reduce bridge dynamics across a typical range of vehicle velocities, proving most effective for road profiles that induce large vibrations in the vehicle–bridge system.

[1]  L Fryba,et al.  VIBRATION OF SOLIDS AND STRUCTURES UNDER MOVING LOADS (3RD EDITION) , 1999 .

[2]  Yonghong Chen,et al.  Smart suspension systems for bridge-friendly vehicles , 2002, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[3]  I. Enevoldsen,et al.  Danish guideline for probability-based assessment of bridges , 2004 .

[4]  J. K. Hedrick,et al.  Active and Semi-Active Heavy Truck Suspensions to Reduce Pavement Damage , 1989 .

[5]  Samuel Grave.  Modelling of site-specific traffic loading on short to medium span bridges , 2002 .

[6]  Darryll J. Pines,et al.  Smart Structures and Materials 2002: Smart Systems for Bridges, Structures, and Highways , 2001 .

[7]  Søren Nielsen,et al.  Heavy Vehicles on Minor Highway Bridges , 1997 .

[8]  George T. Michaltsos,et al.  Dynamic Response of a Bridge With Surface Deck Irregularities , 2000 .

[9]  M. W. Sayers.  Interpretation of road roughness profile data. Final report , 1996 .

[10]  Michael Valášek,et al.  Development of semi-active road-friendly truck suspensions , 1998 .

[11]  Arturo González,et al.  The development of a dynamic amplification estimator for bridges with good road profiles , 2006 .

[12]  Victor DeBrunner,et al.  Adaptive vibration control of a bridge and heavy truck , 2003, IEEE IV2003 Intelligent Vehicles Symposium. Proceedings (Cat. No.03TH8683).

[13]  David Cebon,et al.  Dynamic interaction between heavy vehicles and highway bridges , 1997 .

[14]  Paul S. Fancher,et al.  A factbook of the mechanical properties of the components for single-unit and articulated heavy trucks. Phase I. Final report , 1986 .

[15]  David Cebon,et al.  Handbook of vehicle-road interaction , 1999 .

[16]  A. Prentice,et al.  Energy and transport , 2007, The Lancet.

[17]  Shirley J. Dyke,et al.  Control of a moving oscillator on an elastic continuum using smart dampers , 2002, Proceedings of the 2002 American Control Conference (IEEE Cat. No.CH37301).

[18]  D I Cooper,et al.  DEVELOPMENT OF SHORT SPAN BRIDGE-SPECIFIC ASSESSMENT LIVE LOADING , 1997 .

[19]  Lawrence A. Bergman,et al.  A novel approach to the calculation of pothole-induced contact forces in MDOF vehicle models , 2004 .

[20]  Michael Valášek,et al.  Extended Ground-Hook - New Concept of Semi-Active Control of Truck's Suspension , 1997 .

[21]  Guangjun Li,et al.  Field test of an intelligent stiffener for bridges at the I-35 Walnut Creek bridge , 1999 .

[22]  M. M. ElMadany,et al.  Design and optimization of truck suspensions using covariance analysis , 1988 .

[23]  In-Won Lee,et al.  Vibration Control of Bridges under Moving Loads , 1998 .

[24]  Parag C. Das,et al.  Safety of bridges , 1997 .