Genetic Algorithm Coupled with the Krawczyk Method for Multi-Objective Design Parameters Optimization of the 3-UPU Manipulator

[1]  Hongtao Wu,et al.  Kinematics analysis of an offset 3-UPU translational parallel robotic manipulator , 2003, Robotics Auton. Syst..

[2]  Yuefa Fang,et al.  Error sensibility analysis of 3-UPU parallel manipulator based on probability distribution , 2011, 2011 Second International Conference on Mechanic Automation and Control Engineering.

[3]  Hao Wang,et al.  Kinematic calibration and investigation of the influence of universal joint errors on accuracy improvement for a 3-DOF parallel manipulator , 2018 .

[4]  S El Hraiech,et al.  Error estimation and sensitivity analysis of the 3-UPU translational parallel robot due to design parameter uncertainties , 2019 .

[5]  Jean-Pierre Merlet,et al.  Accounting for tolerances in the design parameters of the 3-RRR , 2016 .

[6]  Zouhaier Affi,et al.  Prediction of the pose errors produced by joints clearance for a 3-UPU parallel robot , 2009 .

[7]  S. M. Varedi,et al.  Kinematics of an offset 3-UPU translational parallel manipulator by the homotopy continuation method , 2009 .

[8]  S. Caro,et al.  Sensitivity analysis of parallel manipulators using an interval linearization method , 2014 .

[9]  Siegfried M. Rump,et al.  INTLAB - INTerval LABoratory , 1998, SCAN.

[10]  Zexiang Li,et al.  Randomized Optimal Design of Parallel Manipulators , 2008, IEEE Transactions on Automation Science and Engineering.

[11]  L. Romdhane,et al.  A combined genetic algorithm-fuzzy logic method (GA-FL) in mechanisms synthesis , 2004 .

[12]  Ming-June Tsai,et al.  Accuracy analysis of a multi-loop linkage with joint clearances , 2008 .

[13]  Singiresu S Rao,et al.  Interval Approach for the Modeling of Tolerances and Clearances in Mechanism Analysis , 2004 .

[14]  S. S. Rao,et al.  Probabilistic approach to manipulator kinematics and dynamics , 2001, Reliab. Eng. Syst. Saf..

[15]  Ajmi Houidi,et al.  Application of multi-objective genetic algorithms to the mechatronic design of a four bar system with continuous and discrete variables , 2013 .

[16]  Ashitava Ghosal,et al.  Optimum design of multi-degree-of-freedom closed-loop mechanisms and parallel manipulators for a prescribed workspace using Monte Carlo method , 2017 .

[17]  Jean-Pierre Merlet.  Interval Analysis for Certified Numerical Solution of Problems in Robotics , 2009, Int. J. Appl. Math. Comput. Sci..

[18]  Madara Ogot,et al.  Dimensional Tolerance Allocation of Stochastic Dynamic Mechanical Systems Through Performance and Sensitivity Analysis , 1993 .

[19]  Zouhaier Affi,et al.  Sensitivity analysis and prediction of the orientation error of a three translational parallel manipulator , 2018 .

[20]  Clément Gosselin,et al.  The Synthesis of Planar Parallel Manipulators with a Genetic Algorithm , 1999 .

[21]  Singiresu S. Rao,et al.  Analysis of uncertain structural systems using interval analysis , 1997 .

[22]  L. Tsai,et al.  Kinematics and Optimization of a Spatial 3-UPU Parallel Manipulator , 2000 .

[23]  Najlawi Bilel,et al.  An improved imperialist competitive algorithm for multi-objective optimization , 2016 .

[24]  S. Agrawal,et al.  Inverse kinematic solution of robot manipulators using interval analysis , 1998 .

[25]  J. McCall,et al.  Genetic algorithms for modelling and optimisation , 2005 .

[26]  Sam Kwong,et al.  Genetic algorithms: concepts and applications [in engineering design] , 1996, IEEE Trans. Ind. Electron..