Method of eliminating velocity ripple in permanent magnet synchronous motor based on internal model principle

This paper addresses the problem of steady-state velocity ripple elimination in permanent magnet synchronous motor(PMSM). The velocity ripples are caused by periodic disturbances in the system, such as: cogging torque, measurement errors of stator current, magnetic flux harmonic, load torque and dead time effect etc. Some of these periodic disturbances affect the speed loop of PMSM vector control system, and the others affect the current loop. Different from the usual way of designing speed loop controller only, according to the generation mechanisms of these periodic disturbances, the speed loop controller and current loop controller are designed based on internal model principle(IMP). The experimental results show that suppressing the velocity ripple in both speed loop and current has a better performance than only in speed loop.

[1]  Eric Rogers,et al.  A Cascade MPC Control Structure for a PMSM With Speed Ripple Minimization , 2013, IEEE Transactions on Industrial Electronics.

[2]  Kheng Cher Yeo,et al.  Adaptive feedforward control to compensate cogging torque and current measurement errors for PMSMs , 2011, 2011 IEEE International Electric Machines & Drives Conference (IEMDC).

[3]  Ya-Jun Pan,et al.  A modular control scheme for PMSM speed control with pulsating torque minimization , 2004, IEEE Transactions on Industrial Electronics.

[4]  Shihua Li,et al.  Disturbance rejection control method for permanent magnet synchronous motor speed-regulation system , 2012 .

[5]  Zongxuan Sun,et al.  A Novel Internal Model-Based Tracking Control for a Class of Linear Time-Varying Systems , 2010 .

[6]  Jun Yang,et al.  Generalized Extended State Observer Based Control for Systems With Mismatched Uncertainties , 2012, IEEE Transactions on Industrial Electronics.

[7]  W.-C. Gan,et al.  Torque and velocity ripple elimination of AC permanent magnet motor control systems using the internal model principle , 2004, IEEE/ASME Transactions on Mechatronics.

[8]  Chung Choo Chung,et al.  IMP based velocity tracking controller for permanent magnet stepper motors , 2011, 2011 8th Asian Control Conference (ASCC).

[9]  Jin Xiaoxiao,et al.  Internal-mode based sliding mode variable structure attitude control of flexible spacecraft , 2014, Proceedings of the 33rd Chinese Control Conference.

[10]  Timothy C. Green,et al.  Internal Model Principle based H∞ Control of a Variable Neutral-Point in an Inverter , 2006 .

[11]  Youyi Wang,et al.  Design of an H/sub /spl infin// controller with internal model principle for disturbance rejection in optical disk drives , 2002, 7th International Conference on Control, Automation, Robotics and Vision, 2002. ICARCV 2002..

[12]  Narayan C. Kar,et al.  Analytical modelling and parametric sensitivity analysis for the PMSM steady-state performance prediction , 2013 .

[13]  Hai-Jiao Guo,et al.  A new control method of BLDCM based on internal model principle , 2003, The Fifth International Conference on Power Electronics and Drive Systems, 2003. PEDS 2003..

[14]  Wang Haihong,et al.  Internal model based optimal tracking control for nonlinear discrete-time systems with sinusoidal disturbances , 2008, 2008 27th Chinese Control Conference.

[15]  Scott D. Sudhoff,et al.  Analysis of Electric Machinery and Drive Systems , 1995 .

[16]  T. Tarczewski,et al.  Torque ripple minimization for PMSM using voltage matching circuit and neural network based adaptive state feedback control , 2014, 2014 16th European Conference on Power Electronics and Applications.

[17]  S.K. Panda,et al.  Speed ripple minimization in PM synchronous motor using iterative learning control , 2005, IEEE Transactions on Energy Conversion.

[18]  Bruce A. Francis,et al.  The internal model principle of control theory , 1976, Autom..

[19]  Shihua Li,et al.  Speed Control for a PMSM Servo System Using Model Reference Adaptive Control and an Extended State Observer , 2014 .

[20]  Z. Zhu,et al.  Influence of design parameters on cogging torque in permanent magnet machines , 1997 .

[21]  D. Howe,et al.  Influence of design parameters on cogging torque in permanent magnet machines , 1997, 1997 IEEE International Electric Machines and Drives Conference Record.