Morphological influences on the electrical sintering process of Aerosol Jet and Ink Jet printed silver microstructures

The morphology of non-sintered printed structures depends on the applied printing process. Aerosol Jet and Ink Jet printed silver structures have been post-treated by furnace and electrical sintering. The resulting different morphologies of the structures were investigated optically by scanning electron microscopy and electrically by measuring the specific electrical resistances. Aerosol Jet printed silver required higher temperature during furnace sintering compared to Ink Jet printed structures to reach the same specific resistance. At temperatures above 200 °C an influence of the printing process on the final electrical resistance was not observed anymore. The electrical sintering with direct current of Aerosol Jet and Ink Jet printed silver microstructures showed lower specific resistances for the aerosol generated structures. Electrical sintering was extended by an electronic regulator module (ERM), which allows the sintering of the printed structures to a specified target resistance. While the average resistance of the structures is depending on accurate adjustment of the ERM, the maximum standard deviation of the resistance values is only 2 % which is much better than in conventional sintering.

[1]  Shlomo Magdassi,et al.  Conductive inks with a "built-in" mechanism that enables sintering at room temperature. , 2011, ACS nano.

[2]  Brian Derby,et al.  A Low Curing Temperature Silver Ink for Use in Ink‐Jet Printing and Subsequent Production of Conductive Tracks , 2005 .

[3]  G. G. Stokes.  "J." , 1890, The New Yale Book of Quotations.

[4]  Ian M. Hutchings,et al.  Direct Writing Technology Advances and Developments , 2008 .

[5]  Esa Kunnari,et al.  Environmental evaluation of new technology: printed electronics case study , 2009 .

[6]  R. Street,et al.  Thermal cure effects on electrical performance of nanoparticle silver inks , 2007 .

[7]  Ben Wang,et al.  Fabrication and characterization of aerosol-jet printed strain sensors for multifunctional composite structures , 2012 .

[8]  Matthias Busse,et al.  INKtelligent printing® for sensorial applications , 2010 .

[9]  David T. W. Lin,et al.  A Flexible Proximity Sensor Fully Fabricated by Inkjet Printing , 2010, Sensors.

[10]  R. German.  Sintering theory and practice , 1996 .

[11]  J. Zalesak,et al.  Silver nanoparticles sintering at low temperature on a copper substrate: In situ characterization under inert atmosphere and air , 2012 .

[12]  Thomas L. Reitz,et al.  Aerosol Jet® Printing of functionally graded SOFC anode interlayer and microstructural investigation by low voltage scanning electron microscopy , 2013 .

[13]  Reijo Tuokko,et al.  Low temperature nanoparticle sintering with continuous wave and pulse lasers , 2011 .

[14]  Ulrich S Schubert,et al.  Roll‐to‐Roll Compatible Sintering of Inkjet Printed Features by Photonic and Microwave Exposure: From Non‐Conductive Ink to 40% Bulk Silver Conductivity in Less Than 15 Seconds , 2012, Advanced materials.

[15]  Ulrich S. Schubert,et al.  Argon plasma sintering of inkjet printed silver tracks on polymer substrates , 2009 .

[16]  Tomi Mattila,et al.  Electrical sintering of nanoparticle structures , 2008, Nanotechnology.

[17]  V. Subramanian,et al.  An ink-jet-deposited passive component process for RFID , 2004, IEEE Transactions on Electron Devices.

[18]  K. C. Yung,et al.  Ink-jet printing and camera flash sintering of silver tracks on different substrates , 2010 .

[19]  K. Jaakkola,et al.  Applicability of Metallic Nanoparticle Inks in RFID Applications , 2009, IEEE Transactions on Components and Packaging Technologies.

[20]  Rui Liu,et al.  Fabrication of platinum-decorated single-walled carbon nanotube based hydrogen sensors by aerosol jet printing , 2012, Nanotechnology.

[21]  M. Busse,et al.  Antibacterial and Abrasion‐Resistant Alumina Micropatterns , 2009 .

[22]  Richard C. Dorf,et al.  The Electrical Engineering Handbook , 1993 .

[23]  Shlomo Magdassi,et al.  The Chemistry of Inkjet Inks , 2009 .

[24]  Frank Kreith,et al.  CRC Handbook of Thermal Engineering , 1999 .

[25]  Marcus Maiwald,et al.  INKtelligent printed strain gauges , 2010 .

[26]  Ulrich S Schubert,et al.  Microwave Flash Sintering of Inkjet‐Printed Silver Tracks on Polymer Substrates , 2009, Advanced materials.

[27]  Alberto Piqué,et al.  Direct-write technologies for rapid prototyping applications : sensors, electronics and integrated power sources , 2002 .

[28]  U. Schubert,et al.  Inkjet printing and low temperature sintering of CuO and CdS as functional electronic layers and Schottky diodes , 2011 .

[29]  Jang Sub Kim,et al.  Direct writing of copper conductive patterns by ink-jet printing , 2007 .

[30]  P. Buffat,et al.  Size effect on the melting temperature of gold particles , 1976 .

[31]  Hyun-Jun Hwang,et al.  In situ monitoring of a flash light sintering process using silver nano-ink for producing flexible electronics , 2013, Nanotechnology.