Gap Waveguide PMC Packaging for Improved Isolation of Circuit Components in High-Frequency Microwave Modules

In this paper, perfect magnetic conductor (PMC)-based packaging technique was used to improve the isolation performance among various microwave circuit components such as high-gain amplifier chains. In this approach, a periodic structure (such as metal pin rows) together with the ground plane of the substrate created a stopband for unwanted parallel plate or cavity modes as well as substrate modes, and thereby suppressed the problems of circuit resonances and related package phenomena. This paper describes two Ka-band amplifier chains that were tested with this new packaging technique. Firstly, a single amplifier chain was tested for maximum stable gain operation, and it was found that the stable gain of was achieved, whereas traditional metal wall package with RF absorber offered stable gain of 40 dB, thus showing significant isolation improvement. Secondly, two high-gain amplifier chains were placed side by side and their mutual isolation was tested. With the proposed gap waveguide packaging, a minimum isolation of 78 dB was achieved, whereas a complete metal shield provided a minimum isolation of only 64 dB over the band of interest.

[3]  P. Dixon,et al.  Cavity-resonance dampening , 2005 .

[4]  Jong-Gwan Yook,et al.  The Use of Metal Filled Via Holes for Improving Isolation in Ltcc RF and Wireless Multichip Packages , 2013 .

[5]  Tatsuo Itoh,et al.  Full-wave analysis of packaged microwave circuits with active and nonlinear devices: an FDTD approach , 1997 .

[6]  E. Rajo-Iglesias,et al.  Local Metamaterial-Based Waveguides in Gaps Between Parallel Metal Plates , 2009, IEEE Antennas and Wireless Propagation Letters.

[7]  T. A. Midford,et al.  The evolution of packages for monolithic microwave and millimeter-wave circuits , 1995 .

[8]  David R. Jackson,et al.  The influence of a top cover on the leakage from microstrip line , 2000, IMS 2000.

[9]  Sung-Jin Kim,et al.  Suppression of leakage resonance in coplanar MMIC packages using a Si sub-mount layer , 2000 .

[10]  Per-Simon Kildal,et al.  Three metamaterial-based gap waveguides between parallel metal plates for mm/submm waves , 2009, 2009 3rd European Conference on Antennas and Propagation.

[11]  S. Wane,et al.  Full-Wave Analysis of Inhomogeneous Deep-Trench Isolation Patterning for Substrate Coupling Reduction and $Q$-Factor Improvement , 2006, IEEE Transactions on Microwave Theory and Techniques.

[12]  Matthew A. Morgan,et al.  Millimeter-wave MMICs and applications , 2003 .

[13]  M. I. Herman,et al.  Isolation in three-dimensional integrated circuits , 2000, IMS 2000.

[14]  D. Sievenpiper,et al.  High-impedance electromagnetic surfaces with a forbidden frequency band , 1999 .

[15]  George V. Eleftheriades,et al.  Metallo-dielectric electromagnetic bandgap structures for suppression and isolation of the parallel-plate noise in high-speed circuits , 2003 .

[16]  P.-S. Kildal,et al.  Parallel Plate Cavity Mode Suppression in Microstrip Circuit Packages Using a Lid of Nails , 2010, IEEE Microwave and Wireless Components Letters.

[17]  E. Rajo-Iglesias,et al.  Packaging of microstrip circuits using bed of springs to suppress cavity modes - A replacement for bed of nails , 2010, 2010 IEEE MTT-S International Microwave Symposium.

[18]  C.B. Ashesh,et al.  Characterization of V-groove coupled microshield line , 2005, IEEE Microwave and Wireless Components Letters.

[19]  A. Mortazawi,et al.  Packaging Method for Increased Isolation Using a Microstrip to Waveguide Transition , 2007, IEEE Microwave and Wireless Components Letters.

[20]  H. Kirino,et al.  A 76 GHz Multi-Layered Phased Array Antenna Using a Non-Metal Contact Metamaterial Waveguide , 2012, IEEE Transactions on Antennas and Propagation.

[21]  Tzong-Lin Wu,et al.  Electromagnetic bandgap power/ground planes for wideband suppression of ground bounce noise and radiated emission in high-speed circuits , 2005, IEEE Transactions on Microwave Theory and Techniques.

[22]  D. F. Williams.  Damping of the resonant modes of a rectangular metal package (MMICs) , 1989 .

[23]  Ahmed A. Kishk,et al.  Numerical Prepackaging with PMC Lid - Efficient and Simple Design Procedure for Microstrip Circuits Including the Packaging , 2012 .

[24]  S. Weinreb,et al.  Full-waveguide band, 90 to 140 GHz, MMIC amplifier module , 1997, 1997 IEEE MTT-S International Microwave Symposium Digest.

[25]  Eva Rajo-Iglesias,et al.  Design and experimental verification of ridge gap waveguide in bed of nails for parallel-plate mode suppression , 2011 .

[26]  A. A. Kishk,et al.  Narrow-Band Microwave Filter Using High-Q Groove Gap Waveguide Resonators With Manufacturing Flexibility and No Sidewalls , 2012, IEEE Transactions on Components, Packaging and Manufacturing Technology.

[27]  Eva Rajo-Iglesias,et al.  Numerical studies of bandwidth of parallel-plate cut-off realised by a bed of nails, corrugations and mushroom-type electromagnetic bandgap for use in gap waveguides , 2011 .

[28]  Jorge R. Costa,et al.  Electromagnetic Characterization of Textured Surfaces Formed by Metallic Pins , 2008, IEEE Transactions on Antennas and Propagation.

[29]  W. H. Haydl,et al.  On the use of vias in conductor-backed coplanar circuits , 2002 .

[30]  P.-S. Kildal,et al.  Experimental Demonstration of Local Quasi-TEM Gap Modes in Single-Hard-Wall Waveguides , 2009, IEEE Microwave and Wireless Components Letters.

[31]  M. Tsuji,et al.  Simultaneous propagation of bound and leaky dominant modes on printed-circuit lines: a new general effect , 1995, Proceedings of 1995 IEEE MTT-S International Microwave Symposium.

[32]  Per-Simon Kildal,et al.  Validation of ridge gap waveguide performance using in-house TRL calibration kit , 2010, Proceedings of the Fourth European Conference on Antennas and Propagation.

[33]  W. H. Haydl.  Resonance phenomena and power loss in conductor-backed coplanar structures , 2000 .

[34]  A. U. Zaman,et al.  Slot antenna in ridge gap waveguide technology , 2012, 2012 6th European Conference on Antennas and Propagation (EUCAP).

[35]  P. Kildal,et al.  Improved Microstrip Filters Using PMC Packaging by Lid of Nails , 2012, IEEE Transactions on Components, Packaging and Manufacturing Technology.

[36]  Nirod K. Das,et al.  Methods of suppression or avoidance of parallel-plate power leakage from conductor-backed transmission lines , 1996 .

[37]  N. Alexopoulos,et al.  Leakage losses for the dominant mode of conductor-backed coplanar waveguide , 1992, IEEE Microwave and Guided Wave Letters.

[38]  Ashraf Uz Zaman,et al.  Using Lid of pins for packaging of microstrip board for descrambling the ports of eleven antenna for radio telescope applications , 2010, 2010 IEEE Antennas and Propagation Society International Symposium.