Computational study of compressive loading of carbon nanotubes using quasi-continuum method

Abstract A reduced-order general continuum method is used to examine the mechanical behavior of single-walled carbon nanotubes (CNTs) under compressive loading and unloading conditions. Quasi-static solutions are sought where the total energy of the system is minimized with respect to the spatial degrees of freedom. The obtained continuum solution is mapped back to the lattice structure of CNTs. We then provide a detailed analysis of buckled configurations for four different types of CNTs on the lattice level and show that, among the cases studied, the armchair CNT has the strongest resistance to the compressive loading. It is also shown that the buckled CNT will significantly lose its structural strength with the zigzag lattice structure. The post-buckling unloading of CNTs demonstrates that, after the occurrence of buckling, the CNT can return to its original state, making its use desirable in fields such as synthetic biomaterials, electromagnetic devices, or polymer composites.

[1]  Robert J. Young,et al.  Modeling the Stress Transfer between Carbon Nanotubes and a Polymer Matrix during Cyclic Deformation , 2009 .

[2]  M. Ortiz,et al.  Subdivision surfaces: a new paradigm for thin‐shell finite‐element analysis , 2000 .

[3]  Marte Gutierrez,et al.  Molecular simulations of cyclic loading behavior of carbon nanotubes using the atomistic finite element method , 2009 .

[4]  David Taniar,et al.  Computational Science and Its Applications - ICCSA 2005, International Conference, Singapore, May 9-12, 2005, Proceedings, Part I , 2005, ICCSA.

[5]  Subra Suresh,et al.  Shell buckling of individual multiwalled carbon nanotubes using nanoindentation , 2005 .

[6]  W. D. Heer,et al.  Electrostatic deflections and electromechanical resonances of carbon nanotubes , 1999, Science.

[7]  Traian Dumitrica,et al.  Symmetry-, time-, and temperature-dependent strength of carbon nanotubes. , 2006, Proceedings of the National Academy of Sciences of the United States of America.

[8]  Lloyd N. Trefethen,et al.  Barycentric Lagrange Interpolation , 2004, SIAM Rev..

[9]  M. Ortiz,et al.  Quasicontinuum analysis of defects in solids , 1996 .

[10]  Jorge Nocedal,et al.  A Limited Memory Algorithm for Bound Constrained Optimization , 1995, SIAM J. Sci. Comput..

[11]  Michael Ortiz,et al.  A cohesive approach to thin-shell fracture and fragmentation , 2005 .

[12]  Ralf Deiterding,et al.  Large-scale fluid-structure interaction simulation of viscoplastic and fracturing thin-shells subjected to shocks and detonations , 2007 .

[13]  Ted Belytschko,et al.  An atomistic-based finite deformation membrane for single layer crystalline films , 2002 .

[14]  Chunyu Li,et al.  Sensors and actuators based on carbon nanotubes and their composites: A review , 2008 .

[15]  Donald W. Brenner,et al.  Mechanical properties of nanotubule fibers and composites determined from theoretical calculations and simulations , 1998 .

[16]  D. Brenner,et al.  Empirical potential for hydrocarbons for use in simulating the chemical vapor deposition of diamond films. , 1990, Physical review. B, Condensed matter.

[17]  Ralf Deiterding,et al.  A Virtual Test Facility for Simulating Detonation-Induced Fracture of Thin Flexible Shells , 2006, International Conference on Computational Science.

[18]  Ryszard Pyrz,et al.  IUTAM Symposium on Modelling Nanomaterials and Nanosystems: Proceedings of the IUTAM Symposium held in Aalborg, Denmark, 19-22 May, 2008 , 2009 .

[19]  William W. Liou,et al.  Computational Study of Compressive Loading of Carbon Nanotubes , 2010, ICCSA.

[20]  Yang Yang,et al.  Atomistic-Based Finite Element Simulation of Carbon Nanotubes , 2008 .