A Clamping Force Performance Evaluation of the Electro Mechanical Brake Using PMSM

This paper deals with clamping force simulation and experimental result of the Electro Mechanical Brake (EMB) for the High-Speed-Train (HST). Three phase Surface Permanent Magnet Synchronous Motor (SPMSM) is applied to the clamping force control of EMB. At the initial development stage, Proportional Integral (PI) current control under synchronous d-q axis frame was applied to the SPMSM torque control. In addition, an anti-windup controller, which is advantageous for fast current tracking, is proposed to improve the torque output. Matlab/Simulink simulation results were compared with the experimental results measured by the clamping force sensors of the EMB test rig. The experimental results were verified compared to the brake design specification of the High-Speed Electric Multiple Unit-430 Experimental (HEMU-430X) train.

[1]  Kunsoo Huh,et al.  Fault-tolerant braking control with integerated EMBs and regenerative in-wheel motors , 2016 .

[2]  Hwi-Beon Shin.  New antiwindup PI controller for variable-speed motor drives , 1998, IEEE Trans. Ind. Electron..

[3]  Mohan Sundar,et al.  Brake-by-Wire, Motivation and Engineering - GM Sequel , 2006 .

[4]  Kihong Park,et al.  Development of a Fail-Safe Control Strategy for Electro-Mechanical Brake System , 2013 .

[5]  Minseok Jang,et al.  Novel clamping force control for electric parking brake systems , 2009, 2009 7th Asian Control Conference.

[6]  Ross Bannatyne.  Advances and Challenges in Electronic Braking Control Technology , 1998 .

[7]  Kunsoo Huh,et al.  Fault Detection and Estimation for Electromechanical Brake Systems Using Parity Space Approach , 2015 .

[8]  허건수,et al.  Electro-Mechanical Brake의 클램핑력 제어를 위한 전류 및 힘 센서 고장 검출 알고리즘 개발 , 2011 .

[9]  Yuqing Zhu,et al.  Adaptive Nonsingular Fast Terminal Sliding Mode Control for Braking Systems with Electro-Mechanical Actuators Based on Radial Basis Function , 2017 .

[10]  Russel J. Kerkman,et al.  A New Synchronous Current Regulator and an Analysis of Current-Regulated PWM Inverters , 1986, IEEE Transactions on Industry Applications.

[11]  Kunsoo Huh,et al.  Fault detection and diagnosis of the electromechanical brake based on observer and parity space , 2012 .

[12]  Salem A. Haggag,et al.  Enhanced Electromechanical Brake-by-Wire System Using Sliding Mode Controller , 2016 .

[13]  Hyun-Sik Ahn,et al.  Design and implementation of a new clamping force estimator in Electro-Mechanical Brake systems , 2013 .

[14]  Min-Soo Kim,et al.  Characteristic Test of the Electro Mechanical Brake Actuator for Urban Railway Vehicles , 2016 .

[15]  Sung-Ho Hwang,et al.  Clamping-Force Control for Electromechanical Brake , 2010, IEEE Transactions on Vehicular Technology.

[16]  Sung-Ho Hwang,et al.  Analysis of a regenerative braking system for Hybrid Electric Vehicles using an Electro-Mechanical Brake , 2009 .

[17]  Jae Seung Cheon,et al.  Brake By Wire System Configuration and Functions using Front EWB (Electric Wedge Brake) and Rear EMB (Electro-Mechanical Brake) Actuators , 2010 .

[18]  Jihun Choi,et al.  Robust Clamping Force Control of an Electro-Mechanical Brake System for Application to Commercial City Buses , 2017 .