Hydrothermal decomposition of brominated epoxy resin in waste printed circuit boards

Abstract Brominated flame retardant (BFR), which containing in printed circuit boards (WPCBs), brings a series of environmental and health problems. Hydrothermal technology was applied to decompose brominated epoxy resin in WPCBs at subcritical or supercritical water conditions. The brominated epoxy resin was decomposed into oil and the environmental influence of BFR was eliminated. The experiment was carried out in a 5.7 ml tube reactor and heated by a salt-bath. The variation of degradation rate of brominated epoxy resin with reaction temperature, time and additives were studied. The compositions of liquid products were analyzed by gas chromatography–mass spectrometry (GC–MS). When reaction temperature exceeded 300 °C, retention time stayed over 30 min and alkaline additive existed, more than 80% brominated epoxy resin could be mainly decomposed into phenol, which can be used as chemical material. Two different hydrothermal decomposition pathways were discussed according to the characterization of products. The results indicated that brominated epoxy resin in WPCBs could be handled effectively by hydrothermal decomposition.

[1]  G. Camino,et al.  Thermal decomposition of fire retardant brominated epoxy resins , 2002 .

[2]  Ǻ. Bergman,et al.  An overview of commercially used brominated flame retardants, their applications, their use patterns in different countries/regions and possible modes of release. , 2003, Environment international.

[3]  Paul T. Williams,et al.  Separation and recovery of materials from scrap printed circuit boards , 2007 .

[4]  Zhigang Shen,et al.  The reuse of nonmetals recycled from waste printed circuit boards as reinforcing fillers in the polypropylene composites. , 2009, Journal of hazardous materials.

[5]  Eric Forssberg,et al.  Mechanical recycling of waste electric and electronic equipment: a review. , 2003, Journal of hazardous materials.

[6]  Shin-ichi Sakai,et al.  Leaching of brominated flame retardants in leachate from landfills in Japan. , 2004, Chemosphere.

[7]  T. Bhaskar,et al.  Alkaline hydrothermal treatment of brominated high impact polystyrene (HIPS-Br) for bromine and bromine-free plastic recovery. , 2006, Chemosphere.

[8]  L. Kong,et al.  Application of hydrothermal reaction in resource recovery of organic wastes , 2008 .

[9]  C. Eckert,et al.  Acid/base-catalyzed ester hydrolysis in near-critical water , 1999 .

[10]  V. Cozzani,et al.  An experimental investigation of tetrabromobisphenol A decomposition pathways , 2004 .

[11]  S. Sakai,et al.  Degradation pathways of decabromodiphenyl ether during hydrothermal treatment. , 2007, Chemosphere.

[12]  Phillip E. Savage,et al.  Recent advances in acid- and base-catalyzed organic synthesis in high-temperature liquid water , 2004 .

[13]  Phillip E. Savage,et al.  Effect of pH on Ether, Ester, and Carbonate Hydrolysis in High-Temperature Water , 2008 .

[14]  Glenn T. Hong,et al.  Corrosion control methods in supercritical water oxidation and gasification processes , 2009 .

[15]  Guangming Li,et al.  WEEE recovery strategies and the WEEE treatment status in China. , 2006, Journal of hazardous materials.

[16]  Naoko Akiya,et al.  Roles of water for chemical reactions in high-temperature water. , 2002, Chemical reviews.

[17]  Z. Aizenshtat,et al.  Thermal behavior of brominated and polybrominated compounds I: closed vessel conditions , 2002 .

[18]  Dan Jensen,et al.  Hydrothermal oxidation of Navy excess hazardous materials , 1998 .

[19]  J. R. Portela,et al.  Elimination of cutting oil wastes by promoted hydrothermal oxidation. , 2001, Journal of hazardous materials.

[20]  P. Savage,et al.  Kinetics and mechanism of p-isopropenylphenol synthesis via hydrothermal cleavage of bisphenol A. , 2004, The Journal of organic chemistry.