Mechanical Properties of Lead-Free Solders

Mechanical testing of solder joint arrays was used to characterize lead-free solder alloys under both shear and tensile loading. The alloys studied included Sn4.0Ag0.5Cu, Sn3.5Ag, Sn0.7Cu, Sn3.0Ag0.5Cu, and Sn1.2Ag0.5Cu0.05Ni. All of the lead-free alloys exhibited time and temperature dependent creep behavior over the entire temperature range from -55 C to 125 C. A SINH creep law was effective in describing the steady state creep behavior over the entire range of conditions. Lead-free alloy strength increases with increasing Ag content. The relative strength of tin-lead versus lead-free alloys depends on the strain rate and temperature regime. At high strain rates and low temperatures, eutectic tin-lead is the strongest alloy. At low strain rates and high temperatures, eutectic tin-lead is the lowest strength alloy. Simulated stress-strain hysteresis loops for both accelerated test and field use conditions showed dramatic differences between the various alloys. Higher Ag content results in a larger stress range but a smaller strain range during temperature cycling.

[1]  R. Darveaux,et al.  Ductile-to-brittle transition strain rate , 2006, 2006 8th Electronics Packaging Technology Conference.

[2]  P. Lall,et al.  Reliability of the aging lead free solder joint , 2006, 56th Electronic Components and Technology Conference 2006.

[3]  M. Ashby,et al.  Deformation-Mechanism Maps: The Plasticity and Creep of Metals and Ceramics , 1982 .

[4]  K. Banerji,et al.  Constitutive relations for tin-based-solder joints , 1992, 1992 Proceedings 42nd Electronic Components & Technology Conference.

[5]  R. Darveaux.  Effect of simulation methodology on solder joint crack growth correlation , 2000, 2000 Proceedings. 50th Electronic Components and Technology Conference (Cat. No.00CH37070).

[6]  J. W. Morris,et al.  Creep properties of Sn-rich solder joints , 2003, 53rd Electronic Components and Technology Conference, 2003. Proceedings..

[7]  A. Dasgupta,et al.  Viscoplastic constitutive properties and energy-partitioning model of lead-free Sn3.9Ag0.6Cu solder alloy , 2003, 53rd Electronic Components and Technology Conference, 2003. Proceedings..

[8]  R. Darveaux,et al.  Interface failure in lead free solder joints , 2006, 56th Electronic Components and Technology Conference 2006.

[9]  Xu Chen,et al.  Modified Anand constitutive model for lead-free solder Sn-3.5Ag , 2004, The Ninth Intersociety Conference on Thermal and Thermomechanical Phenomena In Electronic Systems (IEEE Cat. No.04CH37543).

[10]  Klaus-Jurgen Wolter,et al.  Microstructural dependence of constitutive properties of eutectic SnAg and SnAgCu solders , 2003, 53rd Electronic Components and Technology Conference, 2003. Proceedings..

[11]  A. Syed.  Accumulated creep strain and energy density based thermal fatigue life prediction models for SnAgCu solder joints , 2004, 2004 Proceedings. 54th Electronic Components and Technology Conference (IEEE Cat. No.04CH37546).

[12]  W. Armstrong,et al.  Aging and creep behavior of Sn3.9Ag0.6Cu solder alloy , 2004, 2004 Proceedings. 54th Electronic Components and Technology Conference (IEEE Cat. No.04CH37546).

[13]  R. Darveaux,et al.  Fatigue analysis of flip chip assemblies using thermal stress simulations and a Coffin-Manson relation , 1991, 1991 Proceedings 41st Electronic Components & Technology Conference.

[14]  J. Pang,et al.  Creep and fatigue characterization of lead free 95.5Sn-3.8Ag-0.7Cu solder , 2004, 2004 Proceedings. 54th Electronic Components and Technology Conference (IEEE Cat. No.04CH37546).

[15]  Robert Darveaux,et al.  Effect of Assembly Stiffness and Solder Properties on Thermal Cycle Acceleration Factors , 2005 .

[16]  R. Darveaux,et al.  Shear deformation of lead free solder joints , 2005, Proceedings Electronic Components and Technology, 2005. ECTC '05..

[17]  Frank Garofalo,et al.  Fundamentals of creep and creep-rupture in metals , 1965 .

[18]  S. Jadhav,et al.  Impression creep testing and constitutive modeling of Sn-based solder interconnects , 2004, The Ninth Intersociety Conference on Thermal and Thermomechanical Phenomena In Electronic Systems (IEEE Cat. No.04CH37543).

[19]  J. Pang,et al.  Bulk solder and solder joint properties for lead free 95.5Sn-3.8Ag-0.7Cu solder alloy , 2003, 53rd Electronic Components and Technology Conference, 2003. Proceedings..

[20]  P. Vianco,et al.  Acceleration models, constitutive equations, and reliability of lead-free solders and joints , 2003, 53rd Electronic Components and Technology Conference, 2003. Proceedings..

[21]  R. Darveaux,et al.  Constitutive relations for tin-based-solder joints , 1992, 1992 Proceedings 42nd Electronic Components & Technology Conference.