Results and Insights on the Impact of Smoke on Digital Instrumentation and Control

Smoke can cause interruptions and upsets in active electronics. Because nuclear power plants are replacing analog with digital instrumentation and control systems, qualification guidelines for new systems are being reviewed for severe environments such as smoke and electromagnetic interference. Active digital systems, individual components, and active circuits have been exposed to smoke in a program sponsored by the U.S. Nuclear Regulatory Commission. The circuits and systems were all monitored during the smoke exposure, indicating any immediate effects of the smoke. The major effect of smoke has been to increase leakage currents (through circuit bridging across contacts and leads) and to cause momentary upsets and failures in digital systems. This report summarizes two previous reports and presents new results from conformal coating, memory chip, and hard drive tests. The report describes practices for mitigation of smoke damage through digital system design, fire barriers, ventilation, fire suppressants, and post fire procedures.

[1]  L. Bruce McClung,et al.  Use of Reduced Emissions Wire in Switchgear Equipments , 1995, IEEE Transactions on Industry Applications.

[2]  Charles E. Rogers,et al.  Corrosivity Test Methods for Polymeric Materials. Part 4- Cone Corrosimeter Test Method , 1994 .

[3]  T. J. Tanaka.  Effects of smoke on functional circuits , 1997 .

[4]  A. Jursa,et al.  Handbook of geophysics and the space environment , 1985 .

[5]  R. T. Wood,et al.  Environmental testing of an experimental digital safety channel , 1996 .

[6]  M. J. Jacobus.  Screening tests of representative nuclear power plant components exposed to secondary environments created by fires , 1986 .

[7]  H. R. Baker,et al.  SURFACE CHEMICAL METHODS OF DISPLACING WATER AND/OR OILS AND SALVAGING FLOODED EQUIPMENT. PART 2. FIELD EXPERIENCE IN RECOVERING EQUIPMENT DAMAGED BY FIRE ABOARD USS CONSTELLATION AND EQUIPMENT SUBJECTED TO SALT-SPRAY ACCEPTANCE TEST , 1961 .

[8]  R. T. Wood,et al.  Functional issues and environmental qualification of digital protection systems of advanced light-water nuclear reactors , 1994 .

[9]  Lennart Cider.  Cleaning and reliability of smoke-contaminated electronics , 1993 .

[10]  Barbara T. Reagor.  Smoke Corrosivity: Generation, Impact, Detection, and Protection , 1992 .

[11]  R. B. Comizzoli,et al.  The Kuwait Environment and Its Effects on Electronic Materials and Components , 1992 .

[12]  R. L. Iman,et al.  Evaluation of low-residue soldering for military and commercial applications: A report from the Low-Residue Soldering Task Force , 1995 .

[13]  S. P. Nowlen.  A summary of the Fire Testing Program at the German HDR Test Facility , 1995 .

[14]  Charles E. Rogers,et al.  Corrosivity Test Methods for Polymeric Materials. Part 1- Radiant Furnace Test Method [1] , 1994 .

[15]  J. D. Sinclair,et al.  Corrosion of Electronics The Role of Ionic Substances , 1988 .

[16]  T. J. Tanaka,et al.  Technical basis for environmental qualification of microprocessor-based safety-related equipment in nuclear power plants , 1998 .

[17]  T. J. Tanaka,et al.  Circuit bridging of components by smoke , 1996 .

[18]  R. P. Frankenthal,et al.  Corrosion of Electronic Materials and Devices , 1986, Science.

[19]  W. E. Vesely,et al.  Digital I&C Systems in Nuclear Power Plants. Risk-Screening of Environmental Stressors and a Comparison of Hardware Unavailability With an Existing Analog System , 1998 .

[20]  H. R. Baker,et al.  Guide to NRL Cleaning and Salvaging Techniques for Reclaiming Equipment Contaminated with Seawater, Oil, and Smoke Deposits. , 1973 .