Comparison of UV‐Curing, Hotmelt, and Pressure Sensitive Adhesive as Roll‐to‐Roll Encapsulation Methods for Polymer Solar Cells

The most distinct advantage of the polymer solar cell is the possibility for roll-to-roll (R2R) fabrication compatibility based on printing and coating processes. The R2R encapsulation is the last crucial process step in the manufacturing workflow and is evaluated in this study. Polymer solar cell modules are directly printed on barrier foil and encapsulated with the same barrier foil either on the backside or on both sides of the device. The three lamination methods comprise of UV-curable epoxy resin, hotmelt, and pressure sensitive adhesive (PSA). It is shown that a single-sided encapsulation with UV-curable adhesive is enough to achieve the same or better lifetime than double-sided encapsulation with all the adhesives utilized here. This is mainly due to the good edge sealing effect of the thin adhesive with no edge bleaching after 900 h of constant illumination. Although the fabrication of the PSA method is the fastest method (in this study) it generates a considerable amount of waste (paper liner) and two lamination steps are required to achieve a sufficient lifetime. We conclude that UV-curing presents the largest advantages of all methods with a good upscaling potential and low embodied energy due to the possibility for single-sided encapsulation.

[1]  S. Guillerez,et al.  Definition of encapsulation barrier requirements: A method applied to organic solar cells , 2011 .

[2]  Nicolas Schiller,et al.  Development of high barrier films on flexible polymer substrates , 2006 .

[3]  Donal D. C. Bradley,et al.  Gravure printing for three subsequent solar cell layers of inverted structures on flexible substrates , 2011 .

[4]  Mikkel Jørgensen,et al.  Upscaling of polymer solar cell fabrication using full roll-to-roll processing. , 2010, Nanoscale.

[5]  Martin A. Green,et al.  Solar cell efficiency tables (version 41) , 2013 .

[6]  F. Krebs,et al.  Edge sealing for low cost stability enhancement of roll-to-roll processed flexible polymer solar cell modules , 2012 .

[7]  Michael C. Villet,et al.  Multilayer barrier films comprising nitrogen spacers between free-standing barrier layers , 2009 .

[8]  P. Scharfer,et al.  Comparison of large scale coating techniques for organic and hybrid films in polymer based solar cells , 2013 .

[9]  Fadong Yan,et al.  Semitransparent OPV modules pass environmental chamber test requirements , 2013 .

[10]  Wei Gong,et al.  The use of polyurethane as encapsulating method for polymer solar cells-An inter laboratory study on outdoor stability in 8 countries , 2012 .

[11]  Miin-Jang Chen,et al.  Thin-film encapsulation of polymer-based bulk-heterojunction photovoltaic cells by atomic layer deposition , 2009 .

[12]  Gregor Schwartz,et al.  Efficient Organic Tandem Solar Cells based on Small Molecules , 2011 .

[13]  Veena Misra,et al.  Encapsulation of organic solar cells with ultrathin barrier layers deposited by ozone-based atomic layer deposition , 2010 .

[14]  Arved C. Hübler,et al.  Printed Paper Photovoltaic Cells , 2011 .

[15]  F. Krebs,et al.  Roll‐to‐Roll fabrication of large area functional organic materials , 2013 .

[16]  Suren A. Gevorgyan,et al.  The ISOS-3 inter-laboratory collaboration focused on the stability of a variety of organic photovoltaic devices , 2012 .

[17]  Suren A. Gevorgyan,et al.  Stability of Polymer Solar Cells , 2012, Advanced materials.

[18]  Markus Hösel,et al.  Roll-to-roll fabrication of polymer solar cells , 2012 .

[19]  Suren A. Gevorgyan,et al.  Accurate characterization of OPVs: Device masking and different solar simulators , 2013 .

[20]  Suren A. Gevorgyan,et al.  Scalability and stability of very thin, roll-to-roll processed, large area, indium-tin-oxide free polymer solar cell modules , 2013 .

[21]  Paul Heremans,et al.  Long-term operational lifetime and degradation analysis of P3HT:PCBM photovoltaic cells , 2011 .

[22]  Christoph J. Brabec,et al.  Solution‐Processed Metallic Nanowire Electrodes as Indium Tin Oxide Replacement for Thin‐Film Solar Cells , 2011 .

[23]  Jin-seong Park,et al.  Thin film encapsulation for flexible AM-OLED: a review , 2011 .

[24]  Frederik C. Krebs,et al.  A life cycle analysis of polymer solar cell modules prepared using roll-to-roll methods under ambient conditions , 2011 .

[25]  Mikkel Jørgensen,et al.  Silver front electrode grids for ITO-free all printed polymer solar cells with embedded and raised topographies, prepared by thermal imprint, flexographic and inkjet roll-to-roll processes. , 2012, Nanoscale.

[26]  P. Blom,et al.  Degradation mechanisms in organic photovoltaic devices , 2012 .

[27]  Markus Hösel,et al.  Solar cells with one-day energy payback for the factories of the future , 2012 .

[28]  Jukka Hast,et al.  High efficient plastic solar cells fabricated with a high-throughput gravure printing method , 2010 .

[29]  Sigurd Wagner,et al.  A single-layer permeation barrier for organic light-emitting displays , 2008 .

[30]  Nicolas Schiller,et al.  Permeation barrier properties of thin oxide films on flexible polymer substrates , 2009 .

[31]  Jin Jang,et al.  Solution processed encapsulation for organic photovoltaics , 2013 .

[32]  H. Hoppe,et al.  Polymer solar cells with enhanced lifetime by improved electrode stability and sealing , 2013 .

[33]  Frederik C. Krebs,et al.  The OE-A OPV demonstrator anno domini 2011 , 2011 .

[34]  F. Krebs,et al.  Stability/degradation of polymer solar cells , 2008 .

[35]  Mikkel Jørgensen,et al.  All printed transparent electrodes through an electrical switching mechanism: A convincing alternative to indium-tin-oxide, silver and vacuum , 2012 .

[36]  T. Lunkenbein,et al.  UV‐Cured, Flexible, and Transparent Nanocomposite Coating with Remarkable Oxygen Barrier , 2012, Advanced materials.

[37]  Frederik C. Krebs,et al.  Production of large-area polymer solar cells by industrial silk screen printing, lifetime considerations and lamination with polyethyleneterephthalate , 2004 .

[38]  S. Forrest,et al.  Reliability and degradation of organic light emitting devices , 1994 .

[39]  Claudia N. Hoth,et al.  Printing highly efficient organic solar cells. , 2008, Nano letters.

[40]  F. Krebs,et al.  A roll-to-roll process to flexible polymer solar cells: model studies, manufacture and operational stability studies , 2009 .

[41]  Won Ho Jo,et al.  Degradation and stability of polymer-based solar cells , 2012 .

[42]  D. Garcia-Alonso,et al.  Atomic layer deposition for photovoltaics: applications and prospects for solar cell manufacturing , 2012 .

[43]  Alexander Lange,et al.  Modified processing conditions for optimized organic solar cells with inkjet printed P3HT:PC61BM active layers , 2013 .

[44]  R. Xalter,et al.  Development of Passive and Active Barrier Coatings on the Basis of Inorganic–Organic Polymers , 2006 .

[45]  Mikkel Jørgensen,et al.  Fast Inline Roll‐to‐Roll Printing for Indium‐Tin‐Oxide‐Free Polymer Solar Cells Using Automatic Registration , 2013 .

[46]  Hyun Wook Kang,et al.  Annealing-free, flexible silver nanowire-polymer composite electrodes via a continuous two-step spray-coating method. , 2013, Nanoscale.

[47]  Mikkel Jørgensen,et al.  It is all in the Pattern—High‐Efficiency Power Extraction from Polymer Solar Cells through High‐Voltage Serial Connection , 2013 .

[48]  Ronn Andriessen,et al.  Evaluation of ink-jet printed current collecting grids and busbars for ITO-free organic solar cells , 2012 .