Optimal design of parallel channel patterns in a micro methanol steam reformer

Abstract This study describes the performance of micro methanol steam reformers with channel widths optimized using the simplified conjugate gradient method (SCGM), which uses a minimum objective function of the H 2 mass fraction standard deviation in channels. A three-dimensional numerical model and optimal simplified conjugate gradient algorithm were built to predict and search for the effects of channel widths and flow rate on the performance of chemical reactions. Furthermore, this simulation model was compared to; and corresponded well with existing experimental data. Distributions of velocity, temperature, and gas concentrations (CH 3 OH, CO, H 2 , and CO 2 ) were predicted, and the methanol conversion ratio was also evaluated. The mole fraction of CO contained in the reformed gas, which is essential to preventing poisoning of the catalyst layers of fuel cells, is also investigated. In the optimization search process, the governing equations use the continuity, momentum, heat transfer, and species equations to evaluate the performance of the steam reformer. The results show that channel width optimization can not only increase the methanol conversion ratio and hydrogen production rate but also decrease the concentration of carbon monoxide. The velocity and mixture gas density distributions in channels are discussed and plotted at various locations for an inlet liquid flow rate of 0.3 cc min −1 . Full development is not obtained in the downstream channel flow, the velocity in channel is increased from 1.28 m s −1 to 2.36 m s −1 at location Y  = 1 mm–32 mm, respectively. This can be attributed to a continuous increase in the lightweight H 2 species as a result of chemical reactions in the channels.

[1]  P. M. Diéguez,et al.  Integration of methanol steam reforming and combustion in a microchannel reactor for H2 production: A CFD simulation study , 2009 .

[2]  Chin-Hsiang Cheng,et al.  Optimal design of baffles locations with interdigitated flow channels of a centimeter-scale proton exchange membrane fuel cell , 2010 .

[3]  Chin-Hsiang Cheng,et al.  A SIMPLIFIED CONJUGATE-GRADIENT METHOD FOR SHAPE IDENTIFICATION BASED ON THERMAL DATA , 2003 .

[4]  Chin‐Hsiang Cheng,et al.  The effects of geometric and operating conditions on the hydrogen production performance of a micro-methanol steam reformer , 2010 .

[5]  Duu-Jong Lee,et al.  Flow field optimization for proton exchange membrane fuel cells with varying channel heights and widths , 2009 .

[6]  Alan F. Jankowski,et al.  Novel proton exchange membrane thin-film fuel cell for microscale energy conversion , 2000 .

[7]  W. Yoon,et al.  Development of a micro fuel processor for PEMFCs , 2004 .

[8]  Masaru Noda,et al.  CFD-based optimal design of manifold in plate-fin microdevices , 2004 .

[9]  L. F. Brown.  A comparative study of fuels for on-board hydrogen production for fuel-cell-powered automobiles , 2001 .

[10]  M. Esashi,et al.  MEMS-Based Polymer Electrolyte Fuel Cell , 2002 .

[11]  W. Yan,et al.  Numerical study of heat and mass transfer in a plate methanol steam micro reformer with methanol catalytic combustor , 2010 .

[12]  Sejin Kwon,et al.  Design, fabrication and testing of a catalytic microreactor for hydrogen production , 2006 .

[13]  Yong Wang,et al.  Development of a soldier-portable fuel cell power system. Part I: A bread-board methanol fuel processor , 2002 .

[14]  A. Rougé,et al.  Microchannel reactors for fast periodic operation: the catalytic dehydration of isopropanol , 2001 .

[15]  Akira Igarashi,et al.  A miniaturized methanol reformer with Si-based microreactor for a small PEMFC , 2006 .

[16]  Evan O. Jones,et al.  High efficiency and low carbon monoxide micro-scale methanol processors , 2004 .

[17]  Robert A Dagle,et al.  Methanol steam reforming for hydrogen production. , 2007, Chemical reviews.

[18]  Longsheng Lu,et al.  Optimal design of complex manifold geometries for uniform flow distribution between microchannels , 2008 .

[19]  M. Kothare,et al.  Novel microfluidic interconnectors for high temperature and pressure applications , 2003 .

[20]  Kwang Ho Song,et al.  Development of the integrated methanol fuel processor using micro-channel patterned devices and its performance for steam reforming of methanol , 2007 .

[21]  Jens R. Rostrup-Nielsen,et al.  Conversion of hydrocarbons and alcohols for fuel cells , 2002 .

[22]  Jamie D. Holladay,et al.  Fuel Processing for Portable Power Applications , 2003 .

[23]  Wolfgang Ehrfeld,et al.  State-of-the-art in microreaction technology : concepts, manufacturing and applications , 1999 .

[24]  W. Yan,et al.  Three-dimensional analysis of a plate methanol steam micro-reformer and a methanol catalytic combustor with different flow channel designs , 2011 .

[25]  S. Lakshminarayanan,et al.  Improved Design of Microchannel Plate Geometry for Uniform Flow Distribution , 2008 .